background image

 11

SECTION 6:  CONTROLS

THROTTLE CONTROL 

The throttle control is located on the engine. It regu-
lates the speed of the engine. See Figure 20.

SAFETY IGNITION SWITCH

The ignition key must be inserted in the switch before
the unit will start. Remove the ignition key when
snow thrower is not in use.

FUEL SHUT-OFF 
VALVE 

The fuel shut-off valve,
located under fuel tank,
controls fuel flow from
tank. (If equipped)
See Figure 19.

Figure 20  

SHIFT LEVER 

(See Figure 21 for Model 602, 642 and 662. See
Figure 22 for Models 614, 644, 664, and 6A4)
The shift lever is located in the center of the handle
panel. The shift lever may be moved into one of six
positions. Run engine with throttle in the fast
position. Use the shift lever to determine ground
speed.
Forward—Five forward speeds: position one (1) is
the slowest; position five (5) is the fastest.
Reverse—One reverse (R) speed. 

NOTE: 

 Model 614, 644, 664, and 6A4 has five

forward positions and two reverse.

AUGER CONTROL CLUTCH 

(See Figure 21 for Model 602, 642 and 662. See
Figure 22 for Models 614, 644, 664, and 6A4)
The auger control clutch is located on the left
handle. Squeeze the auger control clutch against the
handle to engage the augers. Release to stop the
snow throwing action. 

TRACTION CONTROL CLUTCH 

(See Figure 21 for Model 602, 642 and 662. See
Figure 22 for Models 614, 644, 664, and 6A4)
The traction control clutch is located on the right
handle. Squeeze the traction control clutch to
engage the wheel drive. Release to stop.

CHUTE DIRECTIONAL CONTROL 

(See Figure 21 for Model 602, 642 and 662. See
Figure 22 for Models 614, 644, 664, and 6A4)
The chute directional control is located on left hand
side of the snow thrower.
To change the direction in which snow is thrown,
turn chute directional control as follows:
Crank clockwise to discharge to the left.
Crank counterclockwise to discharge to the right. 

Figure 21  

Figure 22  

Figure 19  

Closed

Open

Ignition

Key

Choke

Throttle

Primer

Starter

Handle

Chute

Directional Control

Auger

Control

Clutch

Traction 

Control

Clutch

Shift

Lever

Models 602, 642 and 662

Shift

Lever

Chute

Directional Control

Auger

Control

Clutch

Traction 

Control

Clutch

Models 614, 644, 664, and 6A4

Summary of Contents for E644F





























Reviews: