MTD E644F Operator'S Manual Download | Manualshive

Page: 17 / 28

background image

17

Figure 29

NOTE:

It may be necessary to loosen the six hex

nuts that fasten the frame to the auger housing to
aid in belt removal.

5.

Roll the front and rear auger belts off the engine
pulley. See Figure 29.

6.

Unhook the idler spring from the hex bolt on the
auger housing. See Figure 30.

7.

Back out the stop bolt to allow the belts to slip
between the bolt and auger pulley.
See Figure 31.

8.

Lift the rear auger belt from the auger pulley,
and slip belt between the support bracket and
the auger pulley. See Figure 31. Repeat this
step for front auger belt.

9.

Replace both auger control belts by following
instructions in reverse order.

DRIVE BELT

1.

Follow steps 1 through 4 of previous
instructions.

2.

Pull idler pulley up, and lift belt off engine pulley,
idler pulley, and friction wheel disc.
See Figure 29.

3.

Back out the stop bolt until the support bracket
rests on the auger pulley. See Figure 31.

4.

Slip belt between friction wheel and friction
wheel disc. See Figure 31. Remove and replace
belt. Reassemble following the instructions in
reverse order.

NOTE:

The support bracket must rest on the stop

bolt after the new belt has been assembled. See
Figure 31.

Figure 30

Figure 31

CHANGING THE FRICTION WHEEL
RUBBER

The rubber on the friction wheel is subject to wear
and should be checked after 25 hours of operation,
and periodically thereafter. Replace the friction
wheel rubber if any signs of wear or cracking are
found.

1.

Drain the gasoline from the snow thrower, or
place a piece of plastic under the gas cap.

2.

Tip the snow thrower up and forward, so that it
rests on the auger housing.

3.

Remove six self-tapping screws from the frame
cover underneath the snow thrower.

4.

Remove the klick pins which secure the wheels,
and remove the wheels from the axle.

Rear

Auger

Belt

Drive

Belt

Engine

Pulley

Front

Auger

Belt

Idler

Pulley

Idler

Pulley

Engine

Pulley

Friction

Wheel

Frame

Support

Bracket

Rear

Auger

Belt

Front

Auger

Pulley

Auger
Pulley

Idler

Spring

Auger

Housing

Support

Bracket

Spring

Stop

Bolt

Friction

Wheel

Disc

Drive Belt

Friction Wheel

Support Bracket

«
...
15
16
17
18
19
...
»

Summary of Contents for E644F





























Reviews:

No comments

Related manuals for E644F

Brand: Batavia Pages: 30

Brand: Douglas Dynamics Pages: 4

Brand: Stihl Pages: 268

Brand: Snapper Pages: 40

Brand: Poulan Pro Pages: 22

Brand: Ryobi Pages: 76

Brand: Snapper Pages: 6

Brand: TOOLCRAFT Pages: 64

Brand: Milwaukee Pages: 28

Brand: Xtreme Garage Pages: 6

Brand: Stiga Pages: 374

Brand: ebm-papst Pages: 11

Brand: RCm Pages: 67

Brand: RCm Pages: 93

Brand: Maruyama Pages: 18

Brand: Maruyama Pages: 52

Brand: Snapper Pages: 56

LINEO 100 V0 ES

Brand: Vortice Pages: 60

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands