MTD E644F Operator'S Manual Download | Manualshive

Page: 9 / 28

background image

9

Figure 12

4.

When correct adjustment is reached, tighten the
hex nut against the cable to lock it in position.

ATTACHING THE CHUTE ASSEMBLY

(Hardware B)

1.

Place chute assembly over chute opening, with
the opening in the chute assembly facing the
front of the unit.

2.

Place chute flange keepers beneath lip of chute
assembly, flat side down.

3.

Insert hex bolt up through chute flange keeper
and chute assembly as shown in Figure 13.
Secure with hex lock nut.

4.

After assembling all three chute flange keepers,
tighten all nuts and bolts securely, then back off
1/4 turn to allow easier movement.

Figure 13

ATTACHING THE CHUTE DIRECTIONAL
CONTROL (Hardware C)

1.

Loosen the two hex nuts which secure the lower
chute directional control support bracket to the
snow thrower housing. See Figure 14.

Figure 14

2.

Place one flat washer over the end of the chute
directional control, then insert the end of the
chute directional control into the hole in the
plastic bushing in the chute bracket. See Figure
15. Place the second flat washer on the chute
directional control, and secure with hairpin clip.

Figure 15

3.

Thread one hex nut onto the eyebolt on the chute
directional control assembly until there is at least
two inches of threads showing between the nut
and the head of the eyebolt. See Figure 16.

Figure 16

4.

Place the eyebolt into the hole located half way
up the left handle. Secure with cupped washer
(cupped side against the handle, see inset) See
Figure 16.

5.

Adjust the chute directional control support
bracket (see figure 15) so that the spiral on the
chute directional control fully engages the teeth
on the chute assembly. Tighten the hex nuts on
the lower chute directional control bracket
securely. Tighten the hex nuts on the eyebolt.

“Z”

Hex

Nut

Cable is

Straight

Chute

Assembly

Hex Bolt

Hex Lock Nut

Chute Flange

Keeper

Carriage Bolts
Hex Lock Nuts

Chute
Directional
Control

Bracket

Hairpin Clip

Chute Directional

Control Bracket

Flat Washer

Chute Directional

Control

Cup
Side

Crown

Side

Left

Handle

Hex Nut

2” of

Threads

Cupped

Washer

Eyebolt

Hex Nut

«
...
7
8
9
10
11
...
»

Summary of Contents for E644F





























Reviews:

No comments

Related manuals for E644F

Brand: Weed Eater Pages: 23

Brand: Yard-Man Pages: 72

SNOW BLADE 120 CM

Brand: Stoeryd Pages: 8

Brand: Weed Eater Pages: 11

Brand: White Outdoor Pages: 28

Brand: FXA Pages: 157

Brand: ebm-papst Pages: 11

Brand: Briggs & Stratton Pages: 12

Brand: SNOWJOE Pages: 16

Brand: Yamaha Pages: 84

Brand: Kongskilde Pages: 8

YARD BROOM II BLOWER UT08510

Brand: Homelite Pages: 16

Brand: Gaggenau Pages: 40

Brand: Haaga Pages: 56

Brand: SereneLife Pages: 24

QUIET BLOW QB1004

Brand: Billy Goat Pages: 12

Brand: Billy Goat Pages: 28

Brand: Kobalt Pages: 18

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands