background image

 7

SECTION 3:  FINDING YOUR MODEL NUMBER

This Operator’s Manual is an important part of your new walk behind. It will help you assemble, prepare and
maintain your walk behind. Please read and understand what it says. 
Before you start to prepare your walk behind for its first use, please locate the model plate and copy the
information from it in this Operator’s Manual. The information on the model plate is very important if you need
help from your dealer or the MTD customer support department. 

• Every walk behind has a model plate. You can locate it by standing behind the unit in the operating

position and looking down at the rear of the deck. 

• The model plate will look like Figure 2.

Figure 2  

SECTION 4:  CALLING CUSTOMER SUPPORT

If you are having difficulty assembling this product or if you have any question regarding the controls,
operation or maintenance of this unit, please call the Customer Support Department. You can reach them by
calling:

1-800-800-7310

Before you call, make sure that you have your model and serial numbers ready. By having the model and
serial numbers ready, you help the Customer Support Representative give you faster service. To find your
unit’s model and serial number, see SECTION 2: FINDING YOUR MODEL NUMBER.

XXX-X-XXX-X-XXX XXXXXXXXXXX

This is where your model number will be.

This is where your serial number will be.

Copy the model number here:

Copy the serial number here:

MTD PRODUCTS INC

CLEVELAND, OHIO  44136

Summary of Contents for Series 580

























Reviews: