background image

I M P O R T A N T   S A F E T Y 

I N S T R U C T I O N S

WARNING - WHEN USING ELECTRICAL PRODUCTS, BASIC PRECAUTIONS 

SHOULD BE FOLLOWED, INCLUDING THE FOLLOWING:

This manual contains information and instructions for proper operation and maintenance of your MTI bath. 

Failure to follow these instructions could result in personal injury, electrical shock or fire.

INSTRUCTIONS PERTAINING TO RISK OF FIRE, ELECTRIC SHOCK, OR INJURY 

TO PERSONS.

READ AND FOLLOW ALL INSTRUCTIONS

!

!

 

Do not permit children to use this unit unless they are closely supervised by an adult at all

times. Supervision is also required when bath is used by an elderly or handicapped individual.

!

   

!

 

Use this unit only for its intended use as described in this manual. Do not use attachments

not recommended by the manufacturer. Never drop or insert any object into any opening.

OWNER’S MANUAL

AND INSTALLATION GUIDE

Thank  you  for  choosing  an  MTIS  BASICS  bath.  You  have  purchased  a 

high-quality acrylic bath, hand-crafted with pride in the USA. We know it will 

give you many years of pleasure. The instructions in this booklet will provide 

you  with  the  information  you  need  to  install  and  operate  this  unit.  This 

information  is  also  available  on  mtiwhirlpools.com.  Our  customer  service 

department is available to answer any additional questions you may have 

pertaining  to  the  installation  and  operation  of  your  bath.  Call  

1-800-783-8827  to  speak  to  our  Service  Department.  For  faster  service,

please  have  your    warranty  registration  number  (serial  number)  ready  when

calling.  The  registration  number  can  be  found  on  the  CSA/UL  label  adhered  to

the exterior surface of the tub. This sticker is typically placed on the exterior

wall of the tub several inches above the pump or blower.

 For free standing tubs,

the lable will be on the inside surface of the access panel.

IMPORTANT: Locate and note 

your serial number on the cover 

of this manual for any future 

service needs.

S A

M P

L E

Summary of Contents for BASICS MBCRFS6632




















Reviews: