background image

1

1

3

2

3

USB-C Sensor:

 Insert the other end of the cable into 

the device.

Plug the USB-C end of the sensor into the CX Flex until it 
clicks.

Flexi-Disc Sensor:

 Peel the red film from the VHB 

adhesive and press firmly onto the product for 1 
minute if the product surface is curved, or 30 seconds 
if it is flat.

System will auto-arm after 1 minute, or arm 
immediately by holding a whitelisted User Card over 
the RFID Icon.

click

2b

2a

CX FLEX

™ SINGLE-POWER 

PRODUCT MANUAL

3

 MTI P/N 063-00308 rev 2 ©2019 MTI All Rights Reserved

www.mtigs.com  |  T:800.426.6844

MERCHANDISING

KEY WHITELIST

Place Authorization Card over the 
RFID icon to register to system. 
LED will be solid blue.

System must be disarmed 

to perform this operation.

Place the User Key over the RFID 
icon you want to add.

If successful 

 unit beeps 2 times

If unsuccessful 

 unit beeps 4 

times (retry)

Repeat process for all User Keys 
until they are successfully added.

To close the whitelist mode, place 
the Authorization Card over the 
RFID icon. Whitelist mode will end 
automatically after 3 minutes of no 
use. LED will be flashing white.

Summary of Contents for CX FLEX Single-Power










Reviews: