MTI Plunger Lock Quick Start Manual Download | Manualshive

Page: 8 / 8

background image

8

MTI P/N 063-00259 rev A ©2019 MTI All Rights Reserved

www.mobiletechinc.com | T:800.426.6844

MTI PLUNGER LOCKS

™

PRODUCT MANUAL

1

2

3

CORRECT DISPOSAL OF PRODUCT

BATTERY

LOCK REMOVAL

Battery Caution

Risk of explosion if battery is replaced by an incorrect

type. Dispose of used batteries according to the

instructions.
Remove batteries of uninstalled locks before storing.

This marking indicates that this product should not be disposed with other household wastes

throughout the EU. To prevent harm to the environment or human health from uncontrolled

waste disposal, recycle it responsibly to promote the sustainable reuse of material resources.

To dispose of used devices contact MTI Global Services Contact Center at 503-648-6500 or

contact local recycling company for proper recycling instructions for electronic devices.

«
...
6
7
8

Summary of Contents for Plunger Lock









Reviews:

No comments

Related manuals for Plunger Lock

Brand: ABB Pages: 26

Brand: Kaadas Pages: 24

Brand: WALDIS Pages: 18

Brand: Abloy Pages: 16

Brand: NCR Pages: 29

Brand: hager Pages: 2

Brand: BENETEK Pages: 11

Brand: Smart Lock Pages: 9

Brand: CDVI Pages: 20

76508L30 Series

Brand: allgood Pages: 5

BKS B-1993 Series

Brand: G-U Pages: 116

Brand: StGuchi Pages: 2

Brand: PDQ Pages: 2

Brand: AGB Pages: 12

Brand: DOM Pages: 103

Brand: HARFO Pages: 16

Brand: Beninca Pages: 2

Brand: danalock Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands