background image

 SECURE PLUG

™ (PATENT PENDING) 

USER GUIDE

12

 MTI P/N 063-00243 rev B ©2018 MTI All Rights Reserved

www.mobiletechinc.com  |  T:800.426.6844

FCC AND ISED STATEMENT

This device complies with Innovation, Science and Economic Development Canada licence-exempt RSS standard(s). Operation is subject to the following 
two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause 
undesired operation of the device.

CAN ICES-3(B)/NMB-3(B)

Le présent appareil est conforme aux CNR Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts de licence. 
L’exploitation est autorisée aux deux conditions suivantes:

(1) il ne doit pas produire de brouillage et (2) l’ utilisateur du dispositif doit étre prêt à accepter tout brouillage radioélectrique reçu, même si ce brouillage 
est susceptible de compromettre le fomctionnement du dispositif.

CAN ICES-3(B)/NMB-3(B) 

The device meets the exemption from the routine evaluation limits in section 2.5 of RSS 102 and compliance with RSS-102 RF exposure, users can obtain 
Canadian information on RF exposure and compliance. 

Le dispositif rencontre l’exemption des limites courantes d’évaluation dans la section 2.5 de RSS 102 et la conformité à l’exposition de RSS-102 rf, 
utilisateurs peut obtenir l’information canadienne sur l’exposition et la conformité de rf. 

This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment should be installed and operated 
with a minimum distance of 20 millimeters between the radiator and your body. 

Cet émetteur ne doit pas être Co-placé ou ne fonctionnant en même temps qu’aucune autre antenne ou émetteur. Cet équipement devrait être installé et 
actionné avec une distance minimum de 20 millimètres entre le radiateur et votre corps.

MTI declares that the radio equipment models 165-00460, 165-00470 and 165-00471 Secure Plug Power distribution units including the 
models 165-00645 and 165-00670 Remote Access Modules in compliance with EU Directive 2014/53/EU.  

The full text of the EU Manufacturer’s Declaration of Conformity is available at the following internet address: www.mobiletechinc.com

This device complies with Part 15 of the FCC Rules.

Caution: If any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the 
equipment.

Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference 
received, including interference that may cause undesired operation.

The grantee is not responsible for any changes or modifications not expressly approved by the party responsible for compliance. Such modifications could 
void the user’s authority to operate the equipment.

The RF Exposure Compliance distance is 20 millimeters.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These 
limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can 
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. 
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or 
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more 
of the following measures:

—Reorient or relocate the receiving antenna.

—Increase the separation between the equipment and receiver.

—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

—Consult the dealer or an experienced radio/TV technician for help.

Technical Data
Model: 165-00471

Operating Frequency: 

125KHz

Operating Temperature: 

0° C to 40° C

Max Power: 

125KHz: <42dBuA/m at 10m

Technical Data
Model: 165-00645 / 165-00670

Operating Frequency: 

125KHz, 2.4GHz: 2405-2480MHz

Operating Temperature: 

0° C to 40° C

Max Power: 

125KHz: <42dBuA/m at 10m

 2.4GHz: 

<20dBm 

FCC ID: 2AA2X-165-ØØ471
Model: 165-00471
FCC Statement

FCC ID: 2AA2X-165-ØØ645-24
Model: 165-00645 / 165-00670
FCC Statement

ISED Certifcation Number: 24439-165ØØ471
Model: 165-00471
ISED Statement

ISED Certifcation Number: 24439-165ØØ64524
Model: 165-00645 / 165-00670
ISED Statement

Merchandising Technologies Inc.
Unit B, 9/F., Great Wall Factory Building 11 Cheung Shun Street,Lai Chi Kok,Kowloon, Hongkong

Summary of Contents for SECURE PLUG 165-00471













Reviews: