MTU 12 V 2000 M50A Operating Instructions Manual Download

Page: 152 / 257

6.2 LOP fault messages

LOP

Fault messages and measuring points (status reports) are displayed as text messages on the LOP dis‐

play (DIS). Explanation of the displayed texts can be gathered by pressing the help key on the

touchscreen. Fault messages can also be caused by faulty sensors/actuators. Contact Service to have

sensors/actuators checked and replaced as necessary if the troubleshooting measures listed in the table

below prove unsuccessful.

Display text

Meaning

Measure

AL RCS Speed De‐

mand Defect

No speed demand signal

1. Check speed demand source sys‐

tem (e. g. from automatic on-board

network).

2. Check LOP visually (→ Page 243).

3. Perform LOP test procedures

(→ Page 245).

4. Check ECU plug connection

(→ Page 238).

5. Check engine wiring (→ Page 234).

AL Shutdown Expect‐

Yellow alarm occurred; Red alarm with

engine shutdown will probably follow

1. Start other genset

as preventive measure.

2. Determine cause of yellow alarm

and rectify.

AL Battery Charge

Fault

Battery not being charged

1. Check power circuit breakers and

fuses.

2. Check transistorized regulator.

AL Press. Monitoring

Fail (EMU)

EMU pressure monitoring failure

Contact Service.

• Have EMU replaced.

AL ECU Defective

ECU 4 is defective

1. Check LOP visually (→ Page 243).

2. Perform LOP test procedures

(→ Page 245).

3. Check ECU plug connection

(→ Page 238).

4. Check engine wiring (→ Page 234).

5. Contact Service.

• Have ECU checked and re‐

placed if required.

AL Output Stage

Bank 1 Fault

Fault message re. power amplifier, cyl‐

inder bank A

1. Check LOP visually (→ Page 243).

2. Perform LOP test procedures

(→ Page 245).

3. Check ECU plug connection

(→ Page 238).

4. Check engine wiring (→ Page 234).

5. Contact Service.

• Have ECU checked and re‐

placed if required.

152 | Troubleshooting | MW15550/06E 2012-02

TIM-ID: 0000008898 - 002

Summary of Contents for 12 V 2000 M50A


































































































































































































































































Search results

Summary of Contents for 12 V 2000 M50A

Reviews:

Related manuals for 12 V 2000 M50A

Brands by name

Popular brands

MTU 12 V 2000 M50A, Operating Instructions Manual

Search results

Summary of Contents for 12 V 2000 M50A

Reviews:

Related manuals for 12 V 2000 M50A

Brands by name

Popular brands