Mueller PMC 40/50 Instructions For Installation And Operation Manual Download

Page: 3 / 24

Table of Contents - Continued

Section 6.0 - Parts Illustrations

6.1

Control Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

6.2

Control Box Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

6.3

Chiller Assembly Model PMC 40/50 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

6.4

Chiller Assembly Parts List Model PMC 40/50 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

6.5

Chiller Assembly Model PMC 70/120 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

6.6

Chiller Assembly Parts List Model PMC 70/120 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

Section 7.0 - Refrigeration Units

7.1

Specifications/Electrical Data for Model PMC 40/50 with 2 HP Unit . . . . . . . . . . . . . . . . . . . . . . . . . . .16

7.2

Specifications/Electrical Data for Model PMC 70/120 with 3.5 HP Unit . . . . . . . . . . . . . . . . . . . . . . . . .16

7.3

Refrigeration Cycle Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

7.4

EPA Refrigerant Regulations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

7.5

Thermal Expansion Valve (TEV) Superheat Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

7.6

Thermal Expansion Valve Superheat Adjustment Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

Section 8.0 - Warranty

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Section 9.0 - Installation and Service Notes

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Summary of Contents for PMC 40/50

























Search results

Summary of Contents for PMC 40/50

Reviews:

Related manuals for PMC 40/50

Brands by name

Popular brands

Mueller PMC 40/50, Instructions For Installation And Operation Manual

Search results

Summary of Contents for PMC 40/50

Reviews:

Related manuals for PMC 40/50

Brands by name

Popular brands