background image

CommPlete Communications Server

iii

Federal Communications Commission Statement

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy, and if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference, in which case the user will be
required to correct the interference at his own expense.

Warning: Changes or modifications to this unit not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.

FCC Regulations for Telephone Line Interconnection

 

1.

 

No repairs are to be made by you. Repairs are to be made only by Multi-Tech Systems or its
licensees. Unauthorized repairs void registration and warranty. Contact Multi-Tech Systems, Inc. for
details of how to have repairs made.

 

2.

 

When trouble is experienced, you must disconnect your modem from the telephone company’s jack
to determine the cause of the trouble, and reconnect your modem only when the trouble is
corrected.

 

3.

 

The modem cannot be connected to pay telephones or party lines.

 

4.

 

If requested by the telephone company, you must notify them of the following before the
CommPlete Communications Server is installed:

 

a.

 

The particular phone line (phone number) to which the connection is to be made.

 

b.

 

The FCC Registration Number:

 

AU7USA-24457-DE-N

 

c.

 

The manufacturer’s name and model number:

 

Multi-Tech Systems Model CC9648 CommPlete Communications Server

NOTE

: If the telephone company notifies you that your device is causing harm, unplug it. The

telephone company may disconnect your service if necessary and also may change its facilities,
equipment, operations or procedures which may affect operation of your equipment. Where
practical, the telephone company must promptly inform you in writing of the temporary disconnect
or change in service, give you the opportunity to make changes allowing uninterrupted service, and
inform you of your rights to bring a complaint to the FCC.

Summary of Contents for CommPlete CC9648



























Reviews: