Multilin SR469 Instruction Manual Download

Page: 147 / 270

DIAGNOSTICS 5.

ACTUAL

VALUES

5-26

SETPOINT ACCESS IS NOW RESTRICTED: IF the passcode security feature is enabled and a valid passcode has been entered,
when the setpoint under S1 SR469 SETUP, PASSCODE, SETPOINT ACCESS: is altered to ‘Restricted’, this message will appear.
Also, any time that Setpoint access is permitted and the access jumper is removed, this message will also appear.

DATE ENTRY WAS NOT COMPLETE: Since the Date setpoint is special, consisting of MM/DD/YYYY, if the enter key is pressed be-
fore all of the information has been entered, this message will appear and the new value will not be store. Another attempt will have to
be made with the complete information.

DATE ENTRY WAS OUT OF RANGE: If and invalid entry is made for the date (eg. 15 entered for month), this message will appear.

TIME ENTRY WAS NOT COMPLETE: Since the Time setpoint is special, consisting of HH/MM/SS.S, if the enter key is pressed before
all of the information has been entered, this message will appear and the new value will not be store. Another attempt will have to be
made with the complete information.

TIME ENTRY WAS OUT OF RANGE: If and invalid entry is made for the time (eg. 35 entered for hour), this message will appear.

NO TRIPS OR ALARMS TO RESET: If the [RESET] key is pressed when there are no trips or alarms present, this message will ap-
pear.

RESET PERFORMED SUCCESSFULLY: If all trip and alarm features that are active can be cleared (i.e. the conditions that caused
these trips and/or alarms are no longer present), then this message will appear when a RESET is performed, indicating that all trips and
alarms have been cleared.

ALL POSSIBLE RESETS HAVE BEEN PERFORMED: If only some of the trip and alarm features that are active can be cleared (ie. the
conditions that caused some of these trips and/or alarms are still present), then this message will appear when a RESET is performed,
indicating that only trips and alarms that could be reset have been reset.

CONDITION IS PRESENT RESET NOT POSSIBLE: If no trip and alarm features that are active can be cleared (ie. the condition that
caused these trips and/or alarms is still present), then this message will appear when the [RESET] key is pressed.

ARE YOU SURE? PRESS [ENTER] TO VERIFY: If the [RESET] key is pressed and resetting of any trip or alarm feature is possible,
this message will appear to ask for verification of the operation. If [RESET] is pressed again while the message is still on the display, the
reset will be performed.

PRESS [ENTER] TO ADD DEFAULT MESSAGE: Anywhere in the SR469 Actual Value Message Structure, if the [ENTER] key is
pressed, this message will appear to prompt the user to press [ENTER] to add a new default message. To add a new default message,
[ENTER] must be pressed while this message is being displayed.

DEFAULT MESSAGE HAS BEEN ADDED: Any time a new default message is added to the Default message list, this message will
appear as verification.

DEFAULT MESSAGE LIST IS FULL: If an attempt is made to add a new default message to the default message list when 20 mes-
sages are already assigned, this message will appear. In order to add a message, one of the existing messages must be removed.

PRESS [ENTER] TO REMOVE MESSAGE: Under S1 SR469 SETUP, DEFAULT MESSAGES, if the[.] key is pressed, immediately
followed by the [ENTER] key, this message will appear to prompt the user to press [ENTER] to remove a default message. To remove
the default message, [ENTER] must be pressed while this message is being displayed.

DEFAULT MESSAGE HAS BEEN REMOVED: Any time a default message is removed from the Default message list, this message will
appear as verification.

DEFAULT MESSAGES 6 of 20 ARE ASSIGNED: This message will appear each time the DEFAULT MESSAGES subgroup of S1
SR469 SETUP is entered. It is intended to notify the user of the number of default messages that are assigned.

INPUT FUNCTION IS ALREADY ASSIGNED: The Assignable Digital Input functions may only be used once. If an attempt is made to
assign the same function to two different switches, this message will appear.

INVALID SERVICE CODE ENTERED: Under S13 SR469 TESTING, MULTILIN USE ONLY, if an invalid code is entered, this message
will appear.

KEY PRESSED HERE IS INVALID: Under certain situations, certain keys have no function (eg. any number key while viewing Actual
Values). If a key is pressed where it should have no function, this message will appear.