background image

Visit 

gomultilink.com

 for new product releases!

INST

ALL

ATION

Cop

yrigh

t © 2019 Multilink I

nc

. A

ll righ

ts r

eser

ved  •  Sp

ecific

ations subjec

t t

o change without notic

e  •  Re

v. 5/10/2019  •

Page 8

Do

cumen

t N

o. 010-028-

A0

 

Section 2:

 

Introduction 

 

Overall Operation

:   

 

The EDP Double Conversion UPS series of power supplies provides filtered and regulated AC output power to operate 

traffic signals, conflict monitors, camera equipment, lighting, and additional applications used in Departments of 

Transportation and Intelligent Traffic Systems (DOT/ITS). These power supplies are designed to normally power an 

intersection or highway system from the commercial AC utility line while maintaining an emergency battery in a state 

of full charge. If the commercial AC line fails for any reason or if line voltage exceeds preset low or high limits, the 

low voltage inverter within the power supply continues to provide power to the intersection or highway system load 

while drawing its operating power from the battery string. After AC utility line power has been restored, the power 

supply will revert to Double Conversion operation, supplying power to the intersection or highway system while 

drawing operational power from the commercial AC utility line and simultaneously recharging the battery string. The 

power supply will continue providing filtered and regulated AC power to the intersection or highway system load with 

zero loss of output power during outages, brownouts, or spikes. 

 

Primary Voltage

:   

 

The EDP Double Conversion series of power supplies have been designed for operation from standard AC utility lines 

with an overall voltage range of 55 to 155 volts for nominal 120VAC/60Hz models. UPS output frequency is matched 

with the AC input frequency. The wide input voltage range is load dependant. Please see Specifications for output load 

requirements regarding input voltage range. 

 

Inverter Operation

 

 

The EDP Double Conversion UPS series provides uninterruptible power in the event of line voltage brownout, spike, 

or failure. During these events, the inverter draws power from the battery string and provides regulated output voltage 

to the load. The point at which the UPS switches to battery power is load dependant. A UPS with greater than 70% 

load and line voltage less than 96V will switch to inverter operation after 1 minute during brownout conditions and 

immediately switch to inverter during spikes and line failures. When input voltage returns within operating range, the 

UPS will automatically return to Double Conversion operation.  Please see Specifications for Acceptance and Detect 

voltages.  

 

Output Over-current Monitoring

 

 

The output of the EDP Double Conversion UPS series provides three preset current limiting functions that will 

disconnect the inverter in the event of overload and short circuit of the output. Over-currents not exceeding 110% of 

the model rated output current will provide 10 minutes of runtime until the inverter is disconnected. At 150% of 

overload, the UPS will provide 10 second power intervals at which time the UPS will automatically attempt to 

provide power to the load until the over-current condition is removed. This condition will test the overload every 45 

seconds. Short circuit conditions rating at 200% of the model rated output current will disconnect the inverter within 

50ms of detection until the short circuit is no longer detected. These features are self-correcting upon removal of 

overload or short circuit.  

 

Bypass Mode

:

 

 

In the event that the output is overloaded for an extended period of time while in Line Mode, the UPS will enter a 

Bypass state. The inverter will be bypassed and the output powered directly from line voltage. This feature is self-

correcting upon removal of the overload and the inverter will begin to operate, providing filtered and regulated output 

voltage. 

 

 

 

 

 

Summary of Contents for EDP Series








































Reviews: