background image

page 18 — ga9.7He 60 Hz geNeRaTOR• OpeRaTiON aNd paRTs maNual — Rev. #1 (04/29/10) 

15

16

18

20

19

21

22

24

17

27

23

26

25

GA-9.7HE

9700

GA-9.7HE

9700

15. 

engine  Oil  drain  plug  –  Remove  this  drain  plug 

when draining of the oil from the engine crankcase 

is required. Fill with recommeded type oil as listed in 

Table 4

16. 

engine Oil dipstick – Remove oil dipstick to check 

engine oil level.

17. 

Fuel drain plug – Remove plug to drain fuel.

18. 

Fuel gauge – This gauge is located on top of the fuel 

tank. Read this gauge to determine when fuel is low.

19. 

spark plug – Provides spark to the ignition system. 

Set spark plug gap to 0.6 - 0.7 mm (0.028 - 0.031 inch) 

Clean spark plug once a week.

20. 

Recoil starter (pull rope) – Manual-starting method. 

Pull the starter grip until resistance is felt, then pull 

briskly and smoothly.

21. 

Fuel Tank/Cap  –  Remove  fuel  cap  to  add  fresh 

unleaded fuel. Fuel tank capacity is 10 gallons (38 

liters).

22. 

Battery – This generator is equipped with a 12 VDC 

battery. Replace with only recommended type battery.

23. 

Choke lever – Used for starting the engine. Close 

the  choke  lever  when  starting  a  cold  engine  or  in 

cold weather conditions. The choke enriches the fuel 

mixture. Open the choke lever if starting a warm engine 

or in warm weather conditions

24. 

muffler/Heat  shield  –  Used  to  reduce  noise  and 

emissions. 

NeveR touch this heat shield when the 

generator/welder is in use. Always allow time for engine 

to cool before servicing.

25. 

Oil  Filter  –  Replace  oil  filter  as  referenced  in 

maintenance section of this manual.

26. 

engine Oil Filler Hole – Remove cap when the adding 

of engine oil is required. See Table 4 for recommended 

type engine oil.

27. 

air  Cleaner  –  Prevents  dirt  and  other  debris  from 

entering the fuel system. Release retaining clips on top 

of  air  filter  cover  to  gain  access  to  filter  element.

 

NeveR run the engine without an air cleaner.

 NOTICE

This 

HONda  engine  is  equipped  with  a  low  oil 

shutdown capability. A built in sensor will automatically 

turn off the engine should the oil level fall below a safe 

operating condition. Make sure the generator is placed 

on level ground. Placing the generator on level ground 

will ensure that the low oil sensor will function properly.

COMpOnents (generatOr)

Figure 4. Generator Components (continued)

Summary of Contents for GA-9.7HE

























































































Reviews: