background image

 MTX70HD RAMMER • OPERATION AND PARTS MANUAL — REV. #2 (10/26/18) — PAGE 7

SAFETY INFORMATION

GENERAL SAFETY

  CAUTION

 

„

NEVER

 operate this equipment without proper protective 

clothing, shatterproof glasses, respiratory protection, 

hearing protection, steel-toed boots and other protective 

devices required by the job or city and state regulations.

 

„

NEVER

 operate this equipment when not 

feeling well due to fatigue, illness or when 

under medication.

 

„

NEVER

 operate this equipment under the infl uence of 

drugs or alcohol. 

 

„

ALWAYS

 check the equipment for loosened threads or 

bolts before starting.

 

„

DO NOT

 use the equipment for any purpose other than 

its intended purposes or applications.

  NOTICE

 

„

This equipment should only be operated by trained and 

qualifi ed personnel 18 years of age and older.

 

„

Whenever necessary, replace nameplate, operation and 

safety decals when they become diffi cult read.

 

„

Manufacturer does not assume responsibility for any 

accident due to equipment modifi cations. Unauthorized 

equipment modifi cation will void all warranties.

 

„

NEVER

 use accessories or attachments that are not 

recommended by Multiquip for this equipment. Damage 

to the equipment and/or injury to user may result.

 

„

ALWAYS

 know the location of the nearest 

fi re extinguisher.

 

„

ALWAYS 

know the location of the nearest 

fi rst aid kit.

 

„

ALWAYS

 know the location of the nearest phone or 

keep a 

phone on the job site.

 Also, know the phone numbers of 

the nearest 

ambulance, doctor 

and 

fi re department. 

This 

information will be invaluable in the case of an emergency.

RAMMER SAFETY

  DANGER

 

„

NEVER

 operate the equipment in an explosive 

atmosphere or near combustible materials. An 

explosion or fi re could result causing severe 

bodily harm or even death.

  WARNING

 

„

NEVER

 disconnect any 

emergency or safety devices.

 

 

These devices are intended for operator safety. 

Disconnection of these devices can cause severe injury, 

bodily harm or even death. Disconnection of any of these 

devices will void all warranties.

 

„

DO NOT

 use this machine on ground that is harder than 

the machine can handle, or for driving pilings or tamping 

rock beds. Furthermore, use of the machine on sloping 

ground, such as the side of an embankment, may make 

the machine unstable and can cause an accident. It can 

also result in premature machine wear due to uneven 

loads on the machine.

  Use the machine with confi dence for tamping earth and 

sand, soil, gravel, and asphalt. 

DO NOT

 use the machine 

for other types of jobs.

  CAUTION

 

„

NEVER 

lubricate components or attempt service on a 

running machine.

  NOTICE

 

„

ALWAYS

 keep the machine in proper running condition.

 

„

Fix damage to machine and replace any broken parts 

immediately.

 

„

ALWAYS

 store equipment properly when it is not being 

used. Equipment should be stored in a clean, dry location 

out of the reach of children and unauthorized personnel.

Summary of Contents for MTX70HD














Reviews:

Related manuals for MTX70HD