Multitech TalkAnytime TA2410 User Manual Download

Page: 33 / 235

TalkAnytime Quick Start Instructions

Phonebook Configuration

Inbound Phonebook

1. Open the TalkAnytime program.

(

Start

TalkAnytime xxx

Configuration

)

2. Go to

Phone Book

Inbound Phonebook

Add Entry

3. In the “Remove Prefix” field, enter the PBX extension to which you want to direct the incoming

TalkAnytime calls.

4. In the “Add Prefix” field, enter the same digits as were entered in the “Remove Prefix” field.

5. In the “Channel Number” field, enter “Hunting.” A “hunting” value means the TalkAnytime unit will

assign the call to the first available channel.
If desired, specific channels can be assigned to specific incoming calls (i.e., to any set of calls received

with a particular incoming dialing pattern).

6. In the “Description” field, enter an identifier (letters and/or digits) that describes the destination of the

incoming TalkAnytime calls. The identifier entered in this field

must match

the identifier used in the

Service

field of the TalkAnytime URL (see the “TalkAnytime URL Configuration” section below). The

description should make the routing of calls easy to understand. (40 characters max.)

7. Repeat steps 2-6 for each inbound phonebook entry. As noted above, each channel of the TalkAnytime

unit can be configured separately, have its own values in the “Remove Prefix” and “Add Prefix” fields

and its own “Description” value. Or all channels can be configured alike. When all entries are complete,

go to step 8.

8. Click

to exit the inbound phonebook screen.

9. Click on

Save Setup

. Highlight

Save and Reboot

. Click

Your starter inbound phonebook configuration is complete.

Summary of Contents for TalkAnytime TA2410












































































































































































































































Search results

Summary of Contents for TalkAnytime TA2410

Reviews:

Related manuals for TalkAnytime TA2410

Brands by name

Popular brands

Multitech TalkAnytime TA2410, User Manual

Search results

Summary of Contents for TalkAnytime TA2410

Reviews:

Related manuals for TalkAnytime TA2410

Brands by name

Popular brands