background image

 

MTIC Installation & Operation Manual

 

 

 

MTIC Manual R6 

Page 13 of 18 

5.2  Output Relays 

All output relays should be protected by an 8 amp (max.) fuse. 

There are 10 isolated relay outputs which can be selected N/O or N/C via 
DIP switches 1 to 10.  Select outputs which coincide with the desired level 
on the probe where control is required. As the MTIC does not latch each 
central point, this needs to be achieved using "hold in" contacts on the 
contactor, as per following example: 

  Hi Alarm on at 1 

  Standby on at 2, off at 7 

  Duty 2 on at 4, off at 8 

Duty 1 on at 6, off at 10 

Figure 12 

– Output Relays 

5.3  Analog Output 

This section is 

white 

in colour on the rear panel. 

see fig #1

 

Figure 13 

– Analog Output 

As can be seen by the diagram the MTIC can drive into a 

maximum 940W if connected as shown. 

It should be noted that the analogue output is non-isolated and 

in certain circumstances will require a loop isolator. 

5.4  Power Connection 

This section is 

red 

in colour on the rear panel. 

MAINS POWER

240VAC
50/60Hz

 

Figure 14 

– Power Connections 

Prior to connecting the power to the controller, the following 

checks should be performed: 

1. Check the controller voltage rating to ensure compatibility. 

2. Check that the function DIP switches have been set for the 

correct defaults.  Connect as follows:- 

A = Active 
N = Neutral 
E = Earth 

Summary of Contents for MTIC



















Reviews: