background image

 

 

© Munters AB, 2018 

 

2

 

Warranty 

Warranty and technical assistance

 

 
Munters products are designed and built to provide reliable and satisfactory performance but cannot be 
guaranteed free of faults; although they are reliable products they can develop unforeseeable defects 
and the user must take this into account and arrange adequate emergency or alarm systems if failure to 
operate could cause damage to the articles for which the Munters plant was required: if this is not done, 
the user is fully responsible for the damage which they could suffer. 
Munters extends this limited warranty to the first purchaser and guarantees its products to be free from 
defects originating in manufacture or materials for one year from the date of delivery, provided that 
suitable transport, storage, installation and maintenance terms are complied with. The warranty does not 
apply if the products have been repaired without express authorization from Munters, or repaired in such 
a way that, in Munters’ judgement, their performance and reliability have been impaired, or incorrectly 
installed, or subjected to improper use. The user accepts total responsibility for incorrect use of the 
products. 
The warranty on products from outside suppliers fitted to the Junction Box, (for example cables, weights, 
etc.) is limited to the conditions stated by the supplier: all claims must be made in writing within eight days 

of the discovery of the defect and within 12 months of the delivery of the defective product. Munters has 
thirty days from the date of receipt in which to take action, and has the right to examine the product at the 
customer’s premises or at its own plant (carriage cost to be borne by the customer). 
Munters at its sole discretion has the option of replacing or repairing, free of charge, products which it 
considers defective, and will arrange for their dispatch back to the customer carriage paid. In the case of 
faulty parts of small commercial value which are widely available (such as bolts, etc.) for urgent dispatch, 
where the cost of carriage would exceed the value of the parts, Munters may authorize the customer 
exclusively to purchase the replacement parts locally; Munters will reimburse the value of the product at 
its cost price. 
Munters will not be liable for costs incurred in demounting the defective part, or the time required to travel 
to site and the associated travel costs. No agent, employee or dealer is authorized to give any further 

guarantees or to accept any other liability on Munters’ behalf in connection with other Munters products, 
except in writing with the signature of one of the Company’s Managers. 
 
 
 

WARNING:

 In the interests of improving the quality of its products and services, Munters reserves the right 

at any time and without prior notice to alter the specifications in this manual. 
 
 
 

The liability of the manufacturer Munters ceases in the event of: 

 

dismantling the safety devices; 

 

use of unauthorized materials; 

 

inadequate maintenance; 

Summary of Contents for RJB-4












Reviews: