IMPORTANT:
1. Water Supply Service Stop Valve, Water Connections and Electrical Connections to be supplied by others in
accordance with local codes.
2. Waste is 1-1/4” Outer Diameter. Drinking Fountain water inlet is 3/8” Outer Diameter copper tube. Bottle
Filler water inlet is 3/8” Outer Diameter copper tube. Water line by others.
3. Completely flush supply lines of all foreign debris before connecting to fixture. Optional Water Filter (WF1), is
available should any problems with taste, odor, color, or sediment arise from the water supply.
4. Do NOT solder tubes inserted into the bottle filler or the fountain strainer as damage to the o-rings on the
push-in fittings may result.
5. All burrs must be removed from outside of cut tubes before inserting into strainer or other components.
6. Provide electrical service to J-Box to power sensor and solenoid valve.
7. This unit must be grounded per the requirements of applicable electrical codes.
8. Fixture operates within water pressure range of 174 kPa (25 psig) to 724 kPa (105 psig). Murdock Mfg. will
not warranty chiller damaged when connected to supply lines with flow pressure lower that 174 kPa (25 psig)
or higher than 724 kPa (105 psig). A pressure regulator must be furnished by others on supply line if inlet
pressure is greater than 724 kPa (105 psig).
9.
Per UPC 609.10-All building water supply systems in which quick acting valves are installed shall be
provided with devices to absorb the hammer caused by high pressure resulting from the quick closing of the
valve. These pressure-absorbing devices shall be approved mechanical devices. Water pressure-absorbing
devices shall be installed as close as possible to the quick closing valve.
PRIOR TO INSTALLATION:
1. Read all installation instructions carefully, before proceeding.
2. Carefully remove all fixture components from packaging, preventing scratching or damage. Inspect fixture
and all parts from damages and all parts that are bolted on.
3. Provide mounting surface, adequate to support the fixture and loads on the fixture.
4. Provide rough-ins as shown on the roughing-in and dimensional drawing, including water supply, drain pipe
and gravel drain well. (See rough-in details)
5. Electrical Receptacle(s) must be wired to a GFCI protected circuit. Fixture must be earth grounded per NEC
(National Electrical Code).
6. Completely flush water supply lines of all foreign debris, before connecting to the fixture.
A152-BF4 SERIES DRINKING FOUNTAIN INSTALLATION:
1. Insert Mounting Frame into the Rough-In Block Out and secure using 1/4”-20 UNC Mounting Hardware
(Provided by Others).
2. Hang Trim Panel on Mounting Frame. Note: The included 1” brackets do not get used with this installation
and the Plastic Spacers are typically not required and can be discarded.
3. Install the eight (8) Threaded Studs into the Wall Mounting Frame.
4. Remove the Drinking Fountain Top by unfastening the Drain Screw and lifting at the front while pulling
forward. Disconnect Tubing from Bubblers by unfastening Ferrule Nuts. Set Top aside in a safe place where
it will not be damaged. Place the Drain Screw in a secure location where it will not be lost.
5. Align Fixture Mounting Points with Studs and slide Fixture to finished wall. Anchor with Nuts and Washers
provided.
6. Assemble P-Trap to Drain Adapter and then Assemble to unit with Phillips Head Screws.
7. Make-up 1-1/4” outer diameter Waste Connection.
8. After thoroughly flushing the 3/8” outer diameter supply line, connect water supply to the 3-Way Divider
Assembly. From the 3-Way Divider Assembly, connect to 1/4” Nominal Copper Tube Inlets, Stops on
Supplies recommended. See Water Tubing Connections for visual.
9. Reconnect 1/4” OD Polyethylene Tube to Bubbler with Ferrule Nuts.
10. Test operation of Bubblers by depressing buttons and adjust the flow rate as required, see Water Tubing
connections for detail. Check all connections and Waste Piping for leaks. Correct if present.
11. Set Drain Gasket on Drain Adapter.
12. Re-install tops to unit by engaging the back clip and securing with Drain Screw.
I N S TA L L AT I O N / M A I N T E N A N C E I N S T R U C T I O N S
CONTEMPORARY WATER COOLERS
I N S TA L L AT I O N / M A I N T E N A N C E I N S T R U C T I O N S
DRINKING FOUNTAINS
A152-BF4
Page 6 of 22
Revised:
02/02/18
7020-951-001
MURDOCK MFG. •
15125 Proctor Avenue • City of Industry, CA 91746 USA
Phone 800-453-7465 or 626-333-2543 • Fax 626-855-4860 • www.murdockmfg.com
Member of
