A152FG-BF4 DRINKING FOUNTAIN INSTALLATION:
1. Insert mounting frame into the rough-in block out and secure using 1/4”-20 UNC mounting hardware
(Provided by Others).
2. Hang Trim Panel on Mounting Frame. Note: The included 1” brackets do not get used with this installation
and the plastic spacers are typically not required and can be discarded.
3. Install the eight (8) threaded studs into the Wall Mounting Frame
4. Carefully remove Drinking Fountain Fixtures from packaging material and Bottom Access Panel to prevent
scratching or damage.
5. Inspect Fixture Housing to ensure all Tubing connections, Bubblers and Pushbuttons have not become loose
during shipping. Correct if necessary.
5. Align Fixture Mounting Points with Studs and slide Fixture to finished wall. Anchor with Nuts and Washers
provided.
6. Assemble P-Trap to Drain Adapter. Position Drain Gasket on Drain Adapter and mount Drain Adapter to
Drinking Fountain Basin with #10-32 x 1” Center Reject Drain Screw.
7. Make-up 1-1/4” outer diameter waste connection.
8. After thoroughly flushing the 3/8” outer diameter supply line, connect water supply to the 3-Way Divider
Assembly. From the 3-Way Divider Assembly, connect to 1/4” Nominal Copper Tube Inlets, Stops on
Supplies recommended. See Water Tubing Connections for visual.
9. Test operation of Bubblers by depressing buttons and adjust the flow rate as required, see Water Tubing
connections for detail. Check all connections and Waste Piping for leaks. Correct if present.
10. Install Bottom Access Panel to complete the installation.
BF3/BF4 BOTTLE FILLER INSTALLATION:
1. With Drinking Fountain installed, connect water supply line from 3-Way Divider Assembly to Bottle Filler.
2. Loosen Slip Nuts to orientate P-Trap to desired direction then tighten Slip Nuts and make up 1-1/4” O.D.
Waste Connection.
3A.
FOR -BF3 ONLY
Make up Air-Line Supply from Pneumatic Valve to Pushbutton.
3B.
FOR -BF4 ONLY
Make up power connections to the ground, neutral & hot within the electrical box.
NOTE: BEFORE PERFORMING STEP 4, REFER TO ELECTRICAL INSTALLATION.
4. Test for leaks and proper operation, and then install the Bottle Filler Panel using the Water Filler Bracket and
secure the Bottle Filler by tightening the Screws under the Bottle Filler.
DRINKING FOUNTAIN START UP:
1. Before connecting power supply, but after thoroughly flushing the supply line, turn on building water supply
and check all connections for leaks.
2. Air within the drinking fountain system or the structure supply piping will cause an irregular bubbler outlet
stream until purged out by incoming water. Covering the bubbler with a clean cup (or similar object) is
recommended when first activating drinking fountain to prevent excessive splashing. Depress front push pad
until steady water stream is achieved.
3. If water flow requires adjustment, insert a slotted narrow blade screwdriver in the hole centered on the
underside of the fixture in the knee clearance area up to the flow regulator. Turning clockwise will increase
flow and turning counterclockwise will decrease flow.
4. Recheck all water connections with water flowing through system.
BOTTLE FILLER START UP:
1.
PUSHBUTTON OPERATED
:Air within the Bottle Filler System or the structure supply piping will cause an
irregular spout outlet stream until purged out by incoming water. Press and hold Pushbutton until steady
water stream is achieved
2.
SENSOR OPERATED:
Hold container to be filled just below the Sensor in the center of the Filler Spout and
then move the container upward and water flow will start automatically. When the container is almost filled,
lower the container below the Sensor until the water stops flowing. (See label on the Bottle Filler.
I N S TA L L AT I O N / M A I N T E N A N C E I N S T R U C T I O N S
CONTEMPORARY WATER COOLERS
I N S TA L L AT I O N / M A I N T E N A N C E I N S T R U C T I O N S
DRINKING FOUNTAINS
A152-BF4
Page 7 of 22
Revised:
02/02/18
7020-951-001
MURDOCK MFG. •
15125 Proctor Avenue • City of Industry, CA 91746 USA
Phone 800-453-7465 or 626-333-2543 • Fax 626-855-4860 • www.murdockmfg.com
Member of
