MURO VISLIDER CH7260 METAL PRO Instruction Manual Download

Page: 4 / 13

Ver: 10/14/2004 4

Removal of strips from Tool

1) Move the feed lever over slightly, and then press on the end of the feed latch as in

photo 3.

2) Move the feed lever back so it no longer centers the fastener as in Photo 4 and

release the feed latch. This frees the screw from the feed latch.

3) Then, pull the strip towards you and then out of the tool as shown in Photo 5. This

action will push over the strip tensioner spring to allow the strip to be removed easily.

It should be noted that
fasteners with large
heads

might not

directly latch into the
screw guide easily. If
this happens, push the
feed lever over with
your finger while
inserting the strip of
screws to latch the
first screw before
using.

3
1

Summary of Contents for VISLIDER CH7260 METAL PRO














Search results

Summary of Contents for VISLIDER CH7260 METAL PRO

Reviews:

Related manuals for VISLIDER CH7260 METAL PRO

Brands by name

Popular brands

MURO VISLIDER CH7260 METAL PRO, Instruction Manual

Search results

Summary of Contents for VISLIDER CH7260 METAL PRO

Reviews:

Related manuals for VISLIDER CH7260 METAL PRO

Brands by name

Popular brands