Murphy PowerView PV1000 Hardware Installation Manual Download

Page: 3 / 18

Table of Contents

Product Information................................................................................................................ 1

Inspecting Package Contents.......................................................................................1

Hardware Installation.............................................................................................................. 2

Dash-Mounted Installation............................................................................................2

Gimbal Mount Installation.............................................................................................3

Wiring Instructions ................................................................................................................. 4

Single Engine ...............................................................................................................4

Dual Engine Static Addressing.....................................................................................5

NMEA Wiring................................................................................................................6

PVA Gages ..................................................................................................................7

Pin Specifications for Deutsch DT04-6P Style Connections.........................................8

Wiring Schematic .........................................................................................................9

Specifications........................................................................................................................ 10

PHASE

OUT

/ DISCONTINUED

Check

Availability

Summary of Contents for PowerView PV1000



















Search results

Summary of Contents for PowerView PV1000

Reviews:

Related manuals for PowerView PV1000

Brands by name

Popular brands

Murphy PowerView PV1000, Hardware Installation Manual

Search results

Summary of Contents for PowerView PV1000

Reviews:

Related manuals for PowerView PV1000

Brands by name

Popular brands