background image

CONGRATULATIONS ON YOUR PURCHASE 

You have selected an exceptional turntable.  Each component used in the construction 
of the mmf-9.1 was selected to provide you with superior performance and the highest 
level of sound reproduction available today.  We know of no turntable that costs as 
much to produce yet sells for so little.  The precise and elegant design of this turntable 
makes it easy to install and operate.  Please take a few moments to read over the 
operating instructions to ensure that you get the best performance from your turntable 
and years of trouble-free service.     

 
SAFETY GUIDELINES 

This product is designed and manufactured to strict quality and safety standards.  
However, you should be aware of the following installation and operation precautions: 
 

1.

 

Take heed of warnings and instructions

  

Read all the instructions before connecting or operating the turntable. 
Keep this manual so you can refer to these safety instructions.  Heed all warnings and 
safety information in these instructions and on the turntable.  Follow all operating 
instructions.

 

 

2.

 

Water and Moisture

  

To reduce the risk of fire or electric shock, do not expose the turntable to moisture or 
water. If the turntable is exposed to moisture, immediately disconnect the power cord 
from the wall. Take the deck to an authorized music hall service center for inspection.  
Do not touch the turntable, power cord, or plug with wet hands.  
 

3.

 

Object or liquid entry

  

Do not allow foreign objects or liquids into the unit. If this happens, immediately 
disconnect the power cord from the wall and take the unit to an authorized music hall 
service center for inspection. 

 
4.

 

Heat 

Keep the turntable away from naked flames, radiators, heat registers, stoves, or any 
other heat-producing appliances (including amplifiers). 
 

5.

 

Climate 

The turntable has been designed for use in moderate climates.  Do not attempt to use 
below 41 degrees Fahrenheit (5 degrees Celsius) or above 95 degrees Fahrenheit (35 
degrees Celsius). 
 

6.

 

Racks and Stands 

Place the turntable on a fixed, level surface strong enough to support its weight.  Do not 
place it on a moveable cart that could tip over.  We recommend only using stands 
approved for use with audio equipment.  See the 

SITING 

section for further 

suggestions.  
 
 

Summary of Contents for mmf-9.1




















Reviews: