Mutoh Ultima Multi-Purpose Cutting Plotter - Operation Instructions
7
AP-75125, Rev 1.3 ; 20/10/04
Table Of Contents
1. REGULATORY AND SAFETY INFORMATION........................................................................................... 9
1.1.
EMC
STATEMENT FOR
CE
M
ARKING
.......................................................................................................... 9
1.2.
FCC
COMPLIANCE
.................................................................................................................................... 9
1.3.
I
MPORTANT NOTE
...................................................................................................................................... 9
1.4.
S
AFETY
L
ABELS
:
S
AFETY
L
ABELS
,
S
YMBOLES DE SECURITE
,
S
ICHERHEITSSYMBOLE
................................. 10
2. INSTALLATION PROCEDURES................................................................................................................ 11
2.1.
P
REPARING THE CUTTING ENVIRONMENT
.................................................................................................. 11
2.2.
P
ARTS LIST
............................................................................................................................................. 12
2.3.
U
NPACKING AND SETTING UP THE
U
LTIMA
C
UTTER
................................................................................... 13
2.4.
C
UTTER PARTS
&
COMPONENTS
.............................................................................................................. 14
2.5.
C
ONNECTING THE CUTTER TO THE COMPUTER
.......................................................................................... 16
2.6.
C
ONNECTING THE POWER CABLE
............................................................................................................. 17
2.7.
I
NSTALLING A TOOL
................................................................................................................................. 18
2.8.
L
OADING MEDIA
...................................................................................................................................... 19
2.8.1. Loading cut sheet media............................................................................................................... 19
2.8.2. Loading roll media......................................................................................................................... 20
2.9.
T
EST SHEET VERIFY EPOS ALIGNMENT
...................................................................................................... 22
2.9.1 EPOS Alignment
→
test plot.......................................................................................................... 22
3. CUTTER CONTROLS ................................................................................................................................. 23
3.1.
U
NDERSTANDING THE
O
PERATION PANEL
................................................................................................. 23
3.2.
D
IRECT KEY ACCESS
............................................................................................................................... 27
3.2.1. Force selection.............................................................................................................................. 27
3.2.2. Speed selection ............................................................................................................................ 28
3.2.3. Offset selection ............................................................................................................................. 28
3.2.4. Tool selection................................................................................................................................ 29
3.2.5. Origin selection ............................................................................................................................. 29
3.2.6. Test selection................................................................................................................................ 30
3.2.7. Presets selection........................................................................................................................... 30
3.3.
C
ONTOUR
C
UTTING
................................................................................................................................ 34
3.4.
S
QUARE DETAILS
.................................................................................................................................... 37
4. CUTTER SETTINGS & SPECIAL FUNCTIONS......................................................................................... 39
4.1.
G
ENERAL PROCEDURE TO CHANGE SETTINGS ON THE CUTTER
.................................................................. 39
4.2.
O
VERVIEW OF
G
ENERAL SETTINGS
.......................................................................................................... 39
4.3.
L
ANGUAGE SELECTION
............................................................................................................................ 40
4.4.
K
EY COMBINATIONS
................................................................................................................................ 41
5. FINETUNING YOUR CUTTER TO OBTAIN MUTOH QUALITY................................................................ 43
5.1.
A
DJUSTING THE KNIFE DEPTH
.................................................................................................................. 43
5.2.
O
FFSET PRINCIPLE
.................................................................................................................................. 45
5.3.
O
FFSET EFFECT
...................................................................................................................................... 45
5.4.
O
FFSET ADJUSTMENT PROCEDURE
.......................................................................................................... 46
5.5.
P
ERFORMING A TEST CUT
........................................................................................................................ 48
5.6.
T
ROUBLESHOOTING
................................................................................................................................ 49
6. ULTIMA CUTTING PLOTTERS - MEDIA COMPATIBILITY & DIMENSIONS ......................................... 51
6.1.
U
LTIMA CUTTING PLOTTERS
:
M
EDIA COMPATIBILITY
.................................................................................. 51
6.2.
P
HYSICAL DIMENSIONS
U
LTIMA
................................................................................................................ 51
Summary of Contents for Ultima 1400
Page 2: ...2 AP 75125 Rev 1 3 20 10 04 ...
Page 4: ...Mutoh Ultima Multi Purpose Cutting Plotter Operation Instructions 4 AP 75125 Rev 1 3 20 10 04 ...
Page 6: ...Mutoh Ultima Multi Purpose Cutting Plotter Operation Instructions 6 AP 75125 Rev 1 3 20 10 04 ...
Page 8: ...Mutoh Ultima Multi Purpose Cutting Plotter Operation Instructions 8 AP 75125 Rev 1 3 20 10 04 ...
