© MuxLab Inc.
94-000902-A SE-000902-A
2321 Rue Cohen, Montreal, Quebec, Canada. H4R 2N7
Tel: (514) 905-0588 Fax: (514) 905-0589
Toll Free (North America): (877) 689-5228
E-mail:
Specifications
Specifications
Environment
HDMI 2.0b
Devices
Blu-Ray, projectors, monitors, TV, PC, laptops, servers supporting HDMI.
Bandwidth
300MHz
Signals
HDMI 2.0b protocol
HDCP 2.2 compliant
HDR10 support
Connectors
Note: Cables not included.
One (1) HDMI receptacle.
One (1) RJ45S for Cat 5e/6 unshielded or shielded twisted pair.
One (1) 3.5mm jack for directional IR (may be set for an emitter or sensor).
One (1) 3.5mm jack for audio insert (on TX)/audio extract (on RX).
One (1) DB9 for the RS232
One (1) 2.1mm locking power connector (may be used with optional power supply, if
PoE is not available).
Maximum Distance
Based on a maximum length of 6.6ft
(2m) of HDMI cable per end.
Cat5e/6: 330ft (100m) up to 4K @ 30Hz
Note: When installed in an electrically noisy environment, an STP cable must be used.
Also, cross-connection reduces the effective distance depending on the grade of
twisted cable used.
Latency
Typical one (1) Frame (16ms), maximum 2 frames (33ms)
Compression
JPG 2000
Bandwidth
500Mbps
Network Requirement
1000BaseT with Jumbo Frame
IR Frequency
38 to 56KHz
RJ45 Pin Configuration
Reverse Polarity Sensitive. Use
EIA/TIA 568A or 586B straight-
through wiring.
RJ45 Link
Pin 1 (R)
Pin 2 (T)
Pin 3 (R)
Pin 6 (T)
Pin 4 (R)
Pin 5 (T)
Pin 7 (R)
Pin 8 (T)
Cable
One (1) Cat 5e/6 or better twisted pair cables required
Power Source
This device supports PoE (PD), an external power supply is not included. It is intended
to be powered via a PoE (PSE) Ethernet Switch. If required, an optional power supply
(500993) may be purchased separately.
PoE
IEEE 802.3af
Power Consumption
Transmitter: 2.85Watt
Receiver: 2.55Watt
Temperature
Operating: 0° to 40°C
Storage: -20° to 85°C
Humidity: Up to 95% non-condensing
Dimensions
5.60” x 5.20” x 1.10” (142mm x 132mm x 28mm)
Weight
1.5lbs (0.68kg)
Compliance
Regulatory: FCC, CE, RoHS
Flammability: 94V0
Warranty
3 years
Order Information
500778-TX DomoStream Transmitter (UPC: 627699907788)
500778-RX DomoStream Receiver (UPC: 627699807781)
DomoStream
500778
Quick Installation Guide
Overview
DomoStream allows HDMI equipment to be extended up to 330ft (100m) at video resolutions up to
4K (3840x2160) @ 30Hz via one (1) Cat5e/6 cable in point-to-point, point-to-multipoint and
multipoint-to-multipoint configurations, by connecting several units to the same local 1Gbps
Ethernet network. DomoStream supports HDR10, enhancing picture quality and detail particularly
in darker or dimly lit scenes. The unit supports the pass-through transmission of the latest audio
formats up to 8 CH LPCM, Dolby Atmos and DTS:X, offering the listener an exceptional and
enveloping sound experience. In addition the unit supports 2 CH audio insert on the TX and audio
extract on the RX. It supports CEC, RS232 and directional IR for control of end devices.
DomoStream is a PoE (PD) device and may be powered by a PoE (PSE) Ethernet Switch.
DomoStream is an excellent addition to any distributed home AV entertainment system, and may
be managed by the combination of the MuxControl App for iOS or Android running on a
Smartphone or Tablet, and the Pro Digital Network Controller (model 500811).
For the point-to-multipoint and multipoint-to-multipoint configuration the Ethernet Switch must
have Gigabit ports, Jumbo Frame capability and DHCP Server capability, and additionally support
the IGMP communication protocol for the multipoint-to-multipoint case. It should also support
PoE (PSE). MuxLab recommends using the Cisco SG350 Series Managed Switches.
Applications
Residential AV systems.
Installation
1.
Identify the connectors on the Transmitter and Receiver as indicated on the product labels, see the
above front and rear product views for further details.
2.
Verify that the distance between the HDMI Transmitter and Receiver is within MuxLab
specifications (see Specifications table for more details).
3.
To install the Transmitter:
3a.
Connect the Transmitter to the HDMI video source with an HDMI compliant cable.
3b.
If the application is point-to-point, then connect one (1) length of Cat 5e/6 (or higher)
grade UTP cable to the RJ45 LINK connector on the Transmitter. If transmitting over
the network, use an Ethernet Switch between Transmitter and Receiver.
4.
To install the Receiver:
4a.
Connect the Receiver to the HDMI display equipment with an HDMI compliant cable.
