M1.3.BT200-BT200M.NLFREN 13112018
5
NL
.1211 . V201301
- 3
–
7. Position and installation:
1. Unscrew the nuts at the bottom, position the machine and calibrate it with the
horizontal rule. Mount the machine with all the screws and to ensure the machine is
stable. Make sure the system is equipped with a good grounding circuit for prevent
electric leakage. And have operation range of ground for skid prevention.
2. Unscrew the nut A on the cabinet body B as shown in
Fig 3
.
Lift the column C; mount it on the machine body B by using the nut A through the
bolt located on the machine body B. If the column becom
e
s loose after a period of
using, tight them immediately. Otherwise the result of damage to the tyre may
happen.
8. Electricity and Pneumatic connections:
Caution: Before installation and connection, check to be sure that the electricity
power supply corresponds to the machine technical data. All the installation of
electric and pneumatic devices must be operated by a professional electrician
.
Connect the compressed air connector which is on the machine right side with
compressed air system. The electric grid that the machine connects to must have
fuses protection device and good outer cover grounding protection. Install the
leakage automatic air switch on the maim power supply, leakage current is set at 30A
Caution: No power plug for this machine, the user should self-connect one power plug no less than 16A as well
as in line with the machine voltage. Or directly connect with the power supply according to the above
requirements
.
9. Adjusting operation:
Turntable Rotation Pedal (Z)
Bead Breaker Pedal (U)
Jaws open and close Pedal (V)
1)
Tread the Turntable Rotation Pedal (Z), Turntable (Y) clockwise rotation; Lift up the Turntable Rotation
Pedal (Z), Turntable (Y) counterclockwise rotation.
2)
Tread Bead Breaker Pedal (U), Bead Breaker shovel (R) close toward inside; release Bead Breaker Pedal (U),
Bead Breaker shovel (R) return to original position.
3)
Tread Jaws open and close Pedal (V), four clamps (G) on the turntable open; tread again, four clamps (G)
close. When the pedal is in the middle position, the four clamps stop moving.
Tyre changer operation is consisted of three parts:
1
）
Breaking the tyre bead
2
）
Demounting the tyre
3
）
Mounting the tyre
Caution: Before any operations, don
’
t wear loose clothing and wear protective hat, gloves, and skid-proof shoes.
Ensure to exhaust the air in the tyre completely, and remove all the wheel weights from the rim.
Fig 4
.1211 . V201301
- 3
–
7. Position and installation:
1. Unscrew the nuts at the bottom, position the machine and calibrate it with the
horizontal rule. Mount the machine with all the screws and to ensure the machine is
stable. Make sure the system is equipped with a good grounding circuit for prevent
electric leakage. And have operation range of ground for skid prevention.
2. Unscrew the nut A on the cabinet body B as shown in
Fig 3
.
Lift the column C; mount it on the machine body B by using the nut A through the
bolt located on the machine body B. If the column becom
e
s loose after a period of
using, tight them immediately. Otherwise the result of damage to the tyre may
happen.
8. Electricity and Pneumatic connections:
Caution: Before installation and connection, check to be sure that the electricity
power supply corresponds to the machine technical data. All the installation of
electric and pneumatic devices must be operated by a professional electrician
.
Connect the compressed air connector which is on the machine right side with
compressed air system. The electric grid that the machine connects to must have
fuses protection device and good outer cover grounding protection. Install the
leakage automatic air switch on the maim power supply, leakage current is set at 30A
Caution: No power plug for this machine, the user should self-connect one power plug no less than 16A as well
as in line with the machine voltage. Or directly connect with the power supply according to the above
requirements
.
9. Adjusting operation:
Turntable Rotation Pedal (Z)
Bead Breaker Pedal (U)
Jaws open and close Pedal (V)
1)
Tread the Turntable Rotation Pedal (Z), Turntable (Y) clockwise rotation; Lift up the Turntable Rotation
Pedal (Z), Turntable (Y) counterclockwise rotation.
2)
Tread Bead Breaker Pedal (U), Bead Breaker shovel (R) close toward inside; release Bead Breaker Pedal (U),
Bead Breaker shovel (R) return to original position.
3)
Tread Jaws open and close Pedal (V), four clamps (G) on the turntable open; tread again, four clamps (G)
close. When the pedal is in the middle position, the four clamps stop moving.
Tyre changer operation is consisted of three parts:
1
）
Breaking the tyre bead
2
）
Demounting the tyre
3
）
Mounting the tyre
Caution: Before any operations, don
’
t wear loose clothing and wear protective hat, gloves, and skid-proof shoes.
Ensure to exhaust the air in the tyre completely, and remove all the wheel weights from the rim.
Fig 4
9 Instellingen
Voetpedaal voor de rotatie van de draaitafel (Z)
Voetpedaal voor het openen/sluiten van de spanklauwen (V)
Voetpedaal van de hielbreker (U)
1.
Druk op de voetpedaal voor de rotatie van de draaitafel (Z), de draaitafel (Y) draait met de klok mee. Til de voetpedaal
(Z), de draaitafel (Y) draait tegen de klok in.
2.
Druk op de voetpedaal voor de hielbreker (U), de hielbreker beweegt naar binnen. Til de pedaal (U), de hielbreker (R)
keert terug naar zijn uitgangspositie.
3.
Druk op de voetpedaal voor het openen/sluiten van de spanklauwen (V), de 4 spanklauwen (G) op de draaitafel gaan
open. Druk op de voetpedaal opnieuw, de 4 spanklauwen (G) sluiten zich. Als de pedaal in de midden positie is, stoppen
de 4 spanklauwen met bewegen.
Een band wisselen gebeurt in 3 stappen:
1. De hiel van de band breken.
2. De band demonteren.
3. De band monteren.
AANDACHT!
Draag nauwsluitende kleren, een hoofdbescherming, handschoenen en antislip
veiligheidsschoenen. Laat de lucht volledig uit de band en verwijder alle balanceergewichten van
de velg.
.1211 . V201301
- 4 -
9.1. Breaking the tyre bead
：
Ensure to exhaust the air in the tyre completely, place the tyre against the rubber
buffer (S). Bring the paddle against the bead about 10mm from the edge of the rim
shown as
Fig 5
. Tread Bead breaker Pedal (U) to push paddle into tyre. Repeat the
above operations on different positions around the tyre and both sides of tyre until tyre
bead is released completely.
9.2. Demounting the tyre :
Ensure to remove all the weights on the wheel rim and to exhaust the air in the tyre completely before this operation.
Apply lubricating grease (or similar lubricant) around the tyre bead. Without the lubricant may lead to badly wear and
tear on tyre.
Clamp the wheel methods shown as below regarded to the ruled dimension:
a- to clamp the wheel from outside:
Tread the Jaws open and close Pedal (V) halfway down to middle, positioning for the four clamps (G) by reference
scale on the Turntable (Y); put the tyre on turntable, hold the rim, and tread the Jaws open and close Pedal (V) until
the wheel is secured by the jaws.
b- to clamp the wheel from inside:
Positioning for the four clamps (G) and let them all closed. Put the tyre on the turntable and tread the Jaws open and
close Pedal (V) to open the clamps thereby lock the wheel in place.
Caution: Check to make sure the wheel firmly secured by the four clamps before next step
.
Lower the Vertical Arm (M) until the Mounting/demounting head (I)
rests next to the edge of the rim, flip the Locking Handle to lock the
Vertical Arm and Swing Arm in position, and also adjust the Rocker Arm
make Mounting/demounting head can raise 2mm-3mm automatically from
the edge of the wheel rim. Insert the Lifting Lever (T) between the tyre
bead and the front section of the mounting/demounting head (I), and move
the tyre above the mounting/demounting head as shown as
Fig 6
.
Caution: Chains, bracelets, loose clothes and anything else close to the rotating parts will bring danger to the
operator
.
With the Lifting Lever held in position, tread the Turntable Rotation Pedal (Z), rotate the Turntable (Y) in a
clockwise direction until the tyre is completely separated from the wheel rim.
For the other side tyre demounting, keep using the lifting lever to lift the tyre, make the other side tyre separated
from the wheel rim.
9.3. Mounting the tyre :
Caution: Check to make sure that the tyre and the wheel rim are of same size before mounting the tyre.
To avoid any damage on type, lubricate the tyre bead and the wheel rim with the lubrication recommended by
manufacturer. Put on the tyre and check the situation
.
Caution: When clamp the wheel rim, don't put your hands on the wheel rim to avoid injury during this
operation
.
Fig 6
Fig 5
Afb. 5
9.1 De hiel van de band breken
1.
Laat de lucht volledig uit de band, plaat de band tegen de rubberen stootblok (S).
2.
Breng de hielbreker tegen de hiel, op ongeveer 10 mm van de rand van de velg,
zoals in afbeelding 5 getoond.
3.
Druk op de pedaal van de hielbreker (U), op deze in de band te duwen.
4. Herhaal deze operatie op verschillende locaties rondom de band en aan beide
zijden, totdat de hiel volledig vrij is.
9.2 De band demonteren
1.
Zorg ervoor dat alle balanceergewichten verwijderd worden, en dat er geen lucht
meer is in de band voor deze te demonteren.
2. Breng smeervet (of gelijkaardig) rondom de bandhiel. Zonder smeermiddel kan de
band gemakkelijk verslijten en scheuren.
3.
Span het wiel op volgens onderstaande instructies, afhankelijk van de afmetingen:
a. Het wiel van buiten opspannen:
Druk op de voetpedaal (V) halverwege, om de 4 spanklauwen (G) volgens de referentieschaal op de draaitafel (Y). Zet de
band op de draaitafel, houd de velg vast en druk op de voetpedaal (V) totdat het wiel door de spanklauwen beveiligd is.
b. Het wiel van binnen opspannen:
Positioneer de 4 spanklauwen (G) en laat deze gesloten. Zet de band op de draaitafel en druk op de voetpedaal (V), om
de spanklauwen te openen en het wiel vast te klemmen.
AANDACHT!
Voor de volgende stap, maak zeker dat het wiel correct opgespannen is.
copyrighted
document
- all
rights
reserved
by
FBC
