background image

 

33

M1.1.TPT1300-TPT2000.NLFREN   08122017

EN

PLATE COMPACTOR

7

GB

Following the assembly directions below, you 
will assemble the plate compactor in a few 
minutes.

Upper Handle

Folding Wheels Kit (Optional)

Slide the wheels over the stub axles. 
Secure with hairpin retainers and flat 
washers.

Unfold the Handle as shown.

Remove the screw from stop switch, align the 
hole in handle with hole in switch. Insert the 
screw into the hole and tighten in the switch.

1.

ASSEMBLY

  

X 2

B

  

X 2

  

Ø14 X 100

X 1

C

  

X 1

Throttle Control

Stop Switch

Unscrew bolt 5X35 from throttle control. 
Secure the Throttle Control onto the Upper 
Handle with a flat washer 5 and the bolt 5X35 
that just were unscrewed.

  

M5

X 1

A

29242UK00M101-改.indd   7

2016/6/23   17:58:36

4  Assembly

Following the assembly directions below, you will 

assemble the plate compactor in a few minutes. 

Unfold the handle as shown

Remove the screw from stop switch, align the hole in 

handle with hole in switch. Insert the screw into the 

hole and tighten in the switch.

Unscrew bolt 5x35 from throttle control.

Secure the throttle control onto the upper handle 

with a flat washer 5 and the bolt 5x35 that just were 

unscrewed.

1.  Slide the wheels over the stub axles. Secure with 

hairpin retainers and flat washers.

Upper handle

Folding wheels kit (optional)

Stop switch

Throttle control

PLATE COMPACTOR

7

GB

Following the assembly directions below, you 
will assemble the plate compactor in a few 
minutes.

Upper Handle

Folding Wheels Kit (Optional)

Slide the wheels over the stub axles. 
Secure with hairpin retainers and flat 
washers.

Unfold the Handle as shown.

Remove the screw from stop switch, align the 
hole in handle with hole in switch. Insert the 
screw into the hole and tighten in the switch.

1.

ASSEMBLY

  

X 2

B

  

X 2

  

Ø14 X 100

X 1

C

  

X 1

Throttle Control

Stop Switch

Unscrew bolt 5X35 from throttle control. 
Secure the Throttle Control onto the Upper 
Handle with a flat washer 5 and the bolt 5X35 
that just were unscrewed.

  

M5

X 1

A

29242UK00M101-改.indd   7

2016/6/23   17:58:36

PLATE COMPACTOR

7

GB

Following the assembly directions below, you 
will assemble the plate compactor in a few 
minutes.

Upper Handle

Folding Wheels Kit (Optional)

Slide the wheels over the stub axles. 
Secure with hairpin retainers and flat 
washers.

Unfold the Handle as shown.

Remove the screw from stop switch, align the 
hole in handle with hole in switch. Insert the 
screw into the hole and tighten in the switch.

1.

ASSEMBLY

  

X 2

B

  

X 2

  

Ø14 X 100

X 1

C

  

X 1

Throttle Control

Stop Switch

Unscrew bolt 5X35 from throttle control. 
Secure the Throttle Control onto the Upper 
Handle with a flat washer 5 and the bolt 5X35 
that just were unscrewed.

  

M5

X 1

A

29242UK00M101-改.indd   7

2016/6/23   17:58:36

PLATE COMPACTOR

7

GB

Following the assembly directions below, you 
will assemble the plate compactor in a few 
minutes.

Upper Handle

Folding Wheels Kit (Optional)

Slide the wheels over the stub axles. 
Secure with hairpin retainers and flat 
washers.

Unfold the Handle as shown.

Remove the screw from stop switch, align the 
hole in handle with hole in switch. Insert the 
screw into the hole and tighten in the switch.

1.

ASSEMBLY

  

X 2

B

  

X 2

  

Ø14 X 100

X 1

C

  

X 1

Throttle Control

Stop Switch

Unscrew bolt 5X35 from throttle control. 
Secure the Throttle Control onto the Upper 
Handle with a flat washer 5 and the bolt 5X35 
that just were unscrewed.

  

M5

X 1

A

29242UK00M101-改.indd   7

2016/6/23   17:58:36

PLATE COMPACTOR

7

GB

Following the assembly directions below, you 
will assemble the plate compactor in a few 
minutes.

Upper Handle

Folding Wheels Kit (Optional)

Slide the wheels over the stub axles. 
Secure with hairpin retainers and flat 
washers.

Unfold the Handle as shown.

Remove the screw from stop switch, align the 
hole in handle with hole in switch. Insert the 
screw into the hole and tighten in the switch.

1.

ASSEMBLY

  

X 2

B

  

X 2

  

Ø14 X 100

X 1

C

  

X 1

Throttle Control

Stop Switch

Unscrew bolt 5X35 from throttle control. 
Secure the Throttle Control onto the Upper 
Handle with a flat washer 5 and the bolt 5X35 
that just were unscrewed.

  

M5

X 1

A

29242UK00M101-改.indd   7

2016/6/23   17:58:36

copyrighted 

document 

- all 

rights 

reserved 

by 

FBC

Summary of Contents for 829700102













































Reviews: