background image

Programming

                                                                

                                        

Programming Control Unit CH_SV V00 

5/9

 

 

4  Operating cycles 

4.1  Reading operating cycles 

This part describes how to start the reading of the operating cycles of the control unit 
 

4.1.1  Start reading 

 

Switch off control unit or lock the emergency Stop button, close door 

 

Press programming button „3“ 

 

Switch on control unit with pressed programming button „3“ or unlock the 
emergency stop button 

 

Approx. 5s later 

S10 

appears on the display 

 

The control unit is ready for reading operating cycles 

 

4.1.2  Select operating cycles 

 

Press the programming button „1“ as often as necessary until the wished operating 
cycles is indicated, counting upwards 

 

S11

 

operating cycles dock leveler 

 

S12

 

operating cycles door 

 

S13

 

operating cycles inflatable shelter 

 

4.1.3  Select operating cycles 

 

If the wished operating cycle is indicated, press programming button „3“ once. 
The display shows flashing -- 

 

Press programming button „1“ once, the number starts automatically from left to 
right. A number with 8 digits will follow 

 

At the end of the number the display shows -- 

 

By pressing the programming button „1“ once again, the number starts a second 
time 

 

By pressing the programming button „3“ the display shows the pre selected 
operating cycles no. 

 

4.2  Finish operating cycles 

 

Select 

S10

 

 

Press programming button „3“ 5s 

 

the display shows the operating cycles accordingly 

 

Note!  

If in the programming mode no push button is pressed for 60s, the changed settings will be 
reset and the control unit will leave the programming mode automatically. 
 

5  Select inflatable shelter On/ Off 

This part describes how to choose the function inflatable shelter on/ off . This function 
is only for the control unit „ i305“. For this the service tool is not necessary. 

 

5.1  Function inflatable shelter On 

 

Dock leveler in resting position and door closed 

 

Press push button door „STOP“ 5s 

 

The two LED´s on the control units are flashing at the same time 

 

Release push button door „STOP“ 

 

Press push button „AUTO“ 

 

On the display appears 

S00

 

Summary of Contents for DS0290020










Reviews: