***Once the receiver is installed you can select your Set Top Box (below).
Unit is shipped in AT&T mode. Match the lit LEDS to your Set Top Box type
.
1) Start with the CableSAT Receiver power disconnected.
2) Using a pen or paperclip, press and hold the “PGM” switch.
3) Connect power to CableSAT Command Receiver.
4) Hold in the “PGM” switch until the “power” and “learn” LEDs are solid.
5) Release the “PGM” switch. Transmitter is now in AUTO LEARN mode.
6) Point the TV’s IR remote control at the IR window on the side panel of the CableSAT Receiver.
7) Press the Channel Up key on the remote control.
8) The learn LED will flicker and the Programmed LED will light solid once the command has been
@@..
learned. The learn LED will then light solid again.
9) Press the Channel Down key on the remote control.
10) Again the Learn LED will flicker and the Programmed LED will light solid once the command
@@
has been learned. Learn LED will light solid again.
11) Press the following keys in succession. Be sure to wait for the Learn and Program LED to light
@@
up as each key is learned.
12) Press: 0, 1, 2, 3, 4, 5, 6, 7, 8, 9, and “Enter” on the remote.
13) All LEDS will flash briefly to indicate that the CableSAT receiver is programmed and ready.
****If you get a red ERROR light, remove power from the receiver and start again.
1) Start with the CableSAT Receiver power disconnected.
2) Using a pen or paperclip, press and hold the “PGM” switch.
3) Connect power to CableSAT Command Receiver.
4) Hold in the “PGM” switch until the “power” and “learn” LEDs are solid.
4) Release the “PGM” switch. Transmitter is now in AUTO LEARN mode.
5) Press and release the switch a 2
nd
time.
6) All LEDS will light briefly, followed by the Power LED. This indicates you are now in the
@..
set top box series of Presets.
7) To select one of the set top boxes listed press the “PGM” switch to cycle through the
@..
Presets. Set Top Boxes are represented in the chart below.
8) Once the desired set top box is displayed, press and hold the “PGM” switch until the red
@@
“error” LED turns solid.
9) Release the “PGM” key. All LEDS will flash briefly to indicate the CableSat Receiver is
@...
programmed and ready for use.
LE
D
LE
A
R
N
M
O
D
E
LE
A
R
N
E
D
C
O
M
M
A
N
D
S
A
T
&
T
C
O
M
C
A
S
T
D
IR
E
C
T
V
V
E
R
IZ
O
N
,
R
C
N
,
G
R
A
N
D
E
M
E
D
IA
C
O
M
,
R
O
G
E
R
S
,
S
U
D
D
E
N
LI
N
K
,
B
E
N
D
,
W
A
V
E
,
C
H
A
R
T
E
R
(
A
R
R
IS
)
T
IM
E
W
A
R
N
E
R
,
C
O
X
,
W
O
W
,
B
R
IG
H
T
H
O
U
S
E
,
C
A
B
LE
V
IS
IO
N
,
O
P
T
IM
U
M
C
H
A
R
T
E
R
(
C
IS
C
O
)
D
IS
H
,
B
E
LL
C
A
N
A
D
A
C
O
X
M
IN
I
B
O
X
1
POWER
2
LEARN
3
PROGRAMMED
4
ERROR
***IR remote Auto Learn Mode.
For use when your Set Top Box is not listed in PRESETS.
