background image

FCC NOTE:

This equipment has been tested and found to comply with the limits for a Class B Digital Device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This equipment generates, uses, and can

radiate radio frequency energy and, if not installed and used in accordance with the instructions,

may cause harmful interference to radio communications. However, there is no guarantee that

interference will not occur in a

particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by turning the equipment off

and on, the user is encouraged to try to correct the interference by one or more of the following

measures:

•Reorient or relocate the receiving antenna.

•Increase the distance between the equipment and receiver

•Connect the equipment to an outlet on a circuit different from that to which the receiver is

connected

•Consult the dealer or an experienced radio/TV technician for help

This equipment complies with Part 15 of the FCC Rules. Operation is subject to the following two

conditions:1. This equipment may not cause harmful interference, 2. This equipment must accept

any interference received, including interference that may cause undesired operation.

Modifications not authorized by the manufacturer may void the user

s authority to operate this

device.

Summary of Contents for MyE Smart Home Gateway










Reviews: