background image

 

The MyGate Q71S Control Board Installation Manual : Printed 11/02/2013 13:16 

15 

 

Selecting the Operating Mode 

Before we program the opening / closing cycles, we first need to establish the cycles operating mode. 
 
The operating mode is selected through DS1 dip-switches. The switches are located to the right hand side 
of the control board (illustrated right): 
 
 
There are three different operating modes: 
 
Step by Step 
Automatic Closing 
Automatic Closing with Multi-occupation 
 

 

STEP by STEP Mode (Automatic closing turned off) 

This operating function turns off the automatic closing. When a START command is given by pressing 
remote control button or:  
 

A first START command makes the gate OPEN. 

A second START command while the gate is opening will STOP the gate.  

A further START command makes the gate CLOSE. 

A START command while the gate is closing will STOP the gate. 

 

To select this operating mode place the DS1 dip-switches as shown right:              

1=OFF   

       

2=OFF    

   

3=OFF 

 

AUTOMATIC CLOSING Mode 

A first START command makes the gate OPEN, once the gate has reached the 
complete opening it stops and the PAUSE-TIME starts. 

When the pause-time elapses the gate automatically CLOSES. 

If a START command is given while the gate is opening, the gate STOPS still.  

A further START command makes the gate CLOSE. 

If a START command is given while the gate is closing, the gate STOPS and 
REVERSES in about 1.5 seconds.  

 

To select this operating mode place the DS1 dip-switches as shown right: 

1=OFF   

       

2=ON    

   

3=OFF 

               

 

Summary of Contents for Q71S



























Reviews: