background image

User’s Manual

11

Warning

Excessive sound pressure from speakers and headphones can cause hearing loss. In order to use this 

product safely, avoid prolonged listening at excessive sound pressure levels.
For the customers in the U.S.A.
This equipment has been tested and found to comply with the limits for a Class A digital device, 

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection 

against harmful interference when the equipment is operated in a commercial environment. This 

equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in 

accordance with the instruction manual, may cause harmful interference to radio communications.

You are cautioned that any changes or modifications not expressly approved in this manual could void 

your authority to operate this equipment.
All interface cables used to connect peripherals must be shielded in order to comply with the limits for 

a digital device pursuant to Subpart B of Part 15 of FCC Rules.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 

(1) this device may not cause harmful interference, and (2) this device must accept any interference 

received, including interference that may cause undesired operation.
This product with the CE marking complies with the EMC Directive issued by the Commission of the 

European Community. Compliance with this directive implies conformity to the following European 

standards:

•  EN55103-1 : Electromagnetic Interference (Emission)
•  EN55103-2 : Electromagnetic Susceptibility (Immunity)

This product is intended for use in the following Electromagnetic Environments: E1 (residential), 

E2 (commercial and light industrial), E3 (urban outdoors), E4 (controlled EMC environment, ex. TV 

studio).

Information on Disposal for Users of Waste

Electrical & Electronic Equipment(private households).

The Wheelie Bin symbol on the products and/or accompanying documents 

means that used electrical and electronic products should not be mixed 

with general household waste. Disposing of this product correctly will help 

save valuable resources and prevent any potential negative effects on 

human health and the environment.

To properly dispose harmful substances and recycle the product, the 

user is obliged to return it at the point of collection of electrical and 

electronic equipment waste. For more information please contact your 

local authorities, waste disposal units or retailer.

Summary of Contents for Manhattan II Phono Board













Reviews: