background image

4/26/2007 

17 

Regulatory Approvals: 
 
Safety: 
UL 1604 (US and Canada) Hazardous Locations, Class I, Zone 2, Group IIC, T4A 
 
EMI:   
EN50081-1:1992, EN55022 – Class A 

FCC Part 15 Class A 

 
EMS:  EN55024:1998 
 

EN61000-4-2:1995 

 

EN61000-4-3:1995 

 

EN61000-4-4:1995 

 

EN61000-4-5:1995 

 

EN61000-4-6:1995 

 
Note: Shielded cables must be used to meet emission standards  
 

 

Ordering Information 
 
PN  

 

 

Description 

 
900B  

Industrial Ethernet switch chassis with 3 slots for optional expansion modules 

900-RM  

 

19" Rack Mount Kit 

900-PM 

 

Panel Mount Kit 

908TX  

 

Eight ports 10/100BaseTX (RJ45) 

902FX-XX  

 

Two ports 100BaseFX multimode fiber 

902FXE-XX-YY  

Two ports 100BaseFX singlemode fiber 

904FX-XX  

 

Four ports 100BaseFX multimode fiber 

904FXE-XX-YY  

Four ports 100BaseFX singlemode fiber 

 
Where "XX" is:  

ST for ST style fiber connector 
SC for SC style fiber connector 
 

Where "YY" is:  

15 for 15km max. fiber segment length 
40 for 40km max. fiber segment length 
80 for 80km max. fiber segment length 

 
Warranty 
 
One Year Parts & Labor 
 
Contact/Support Information 
 
N-TRON Corp. 
820 S. University Blvd., Suite 4E 
Mobile, AL  36609 
TEL (251) 342-2164  
FAX (251) 342-6353 
Website: 

www.n-tron.com

 

E-Mail: support@n-tron.com 

Summary of Contents for 900



















Reviews: