background image

4/26/2007 

18 

N-TRON Limited Warranty 

 

N-TRON, Corp. warrants to the end user that this hardware product will be free from defects in workmanship and materials, under normal use 
and service, for the applicable warranty period from the date of purchase from N-TRON or its authorized reseller.  If a product does not operate 
as  warranted  during  the  applicable  warranty  period,  N-TRON  shall,  at  its  option  and  expense,  repair  the  defective  product  or  part,  deliver  to 
customer an equivalent product or part to replace the defective item, or refund to customer the purchase price paid for the defective product.  All 
products that are replaced will become the property of N-TRON.  Replacement products may be new or reconditioned.  Any replaced or repaired 
product  or  part  has  a  ninety  (90)  day  warranty  or  the  remainder  of  the  initial  warranty  period,  whichever  is  longer.    N-TRON  shall  not  be 
responsible for any custom software or firmware, configuration information, or memory data of customer contained in, stored on, or integrated 
with any products returned to N-TRON pursuant to any warranty. 
 
OBTAINING WARRANTY SERVICE: Customer must contact N-TRON within the applicable warranty period to obtain warranty service 
authorization.  Dated proof of purchase from N-TRON or its authorized reseller may be required.  Products returned to N-TRON must be pre-
authorized by N-TRON with a Return Material Authorization (RMA) number marked on the outside of the package, and sent prepaid and 
packaged appropriately for safe shipment. Responsibility for loss or damage does not transfer to N-TRON until the returned item is received by 
N-TRON.  The repaired or replaced item will be shipped to the customer, at N-TRON’s expense, not later than thirty (30) days after N-TRON 
receives the product.  N-TRON shall not be responsible for any software, firmware, information, or memory data of customer contained in, 
stored on, or integrated with any products returned to N-TRON for repair, whether under warranty or not. 
 
ADVANCE REPLACEMENT OPTION:  Upon registration, this product qualifies for advance replacement.  A replacement product will be 
shipped within three (3) days after verification by N-TRON that the product is considered defective.  The shipment of advance replacement 
products is subject to local legal requirements and may not be available in all locations.  When an advance replacement is provided and 
customer fails to return the original product to N-TRON within fifteen (15) days after shipment of the replacement, N-TRON will charge 
customer for the replacement product, at list price. 
 
WARRANTIES EXCLUSIVE: IF AN N-TRON PRODUCT DOES NOT OPERATE AS WARRANTED ABOVE, CUSTOMER'S SOLE 
REMEDY FOR BREACH OF THAT WARRANTY SHALL BE REPAIR, REPLACEMENT, OR REFUND OF THE PURCHASE PRICE 
PAID, AT N-TRON'S OPTION. TO THE FULL EXTENT ALLOWED BY LAW, THE FOREGOING WARRANTIES AND REMEDIES 
ARE EXCLUSIVE AND ARE IN LIEU OF ALL OTHER WARRANTIES, TERMS, OR CONDITIONS, EXPRESS OR IMPLIED, EITHER 
IN FACT OR BY OPERATION OF LAW, STATUTORY OR OTHERWISE, INCLUDING WARRANTIES, TERMS, OR CONDITIONS OF 
MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, SATISFACTORY QUALITY, CORRESPONDENCE WITH 
DESCRIPTION, AND NON-INFRINGEMENT, ALL OF WHICH ARE EXPRESSLY DISCLAIMED. N-TRON NEITHER ASSUMES NOR 
AUTHORIZES ANY OTHER PERSON TO ASSUME FOR IT ANY OTHER LIABILITY IN CONNECTION WITH THE SALE, 
INSTALLATION, MAINTENANCE OR USE OF ITS PRODUCTS. N-TRON SHALL NOT BE LIABLE UNDER THIS WARRANTY IF 
ITS TESTING AND EXAMINATION DISCLOSE THAT THE ALLEGED DEFECT OR MALFUNCTION IN THE PRODUCT DOES NOT 
EXIST OR WAS CAUSED BY CUSTOMER'S OR ANY THIRD PERSON'S MISUSE, NEGLECT, IMPROPER INSTALLATION OR 
TESTING, UNAUTHORIZED ATTEMPTS TO OPEN, REPAIR OR MODIFY THE PRODUCT, OR ANY OTHER CAUSE BEYOND THE 
RANGE OF THE INTENDED USE, OR BY ACCIDENT, FIRE, LIGHTNING, POWER CUTS OR OUTAGES, OTHER HAZARDS, OR 
ACTS OF GOD.  
 
LIMITATION OF LIABILITY: TO THE FULL EXTENT ALLOWED BY LAW, N-TRON ALSO EXCLUDES FOR ITSELF AND ITS 
SUPPLIERS ANY LIABILITY, WHETHER BASED IN CONTRACT OR TORT (INCLUDING NEGLIGENCE), FOR INCIDENTAL, 
CONSEQUENTIAL, INDIRECT, SPECIAL, OR PUNITIVE DAMAGES OF ANY KIND, OR FOR LOSS OF REVENUE OR PROFITS, 
LOSS OF BUSINESS, LOSS OF INFORMATION OR DATA, OR OTHER FINANCIAL LOSS ARISING OUT OF OR IN CONNECTION 
WITH THE SALE, INSTALLATION, MAINTENANCE, USE, PERFORMANCE, FAILURE, OR INTERRUPTION OF ITS PRODUCTS, 
EVEN IF N-TRON OR ITS AUTHORIZED RESELLER HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES, AND 
LIMITS ITS LIABILITY TO REPAIR, REPLACEMENT, OR REFUND OF THE PURCHASE PRICE PAID, AT N-TRON'S OPTION. THIS 
DISCLAIMER OF LIABILITY FOR DAMAGES WILL NOT BE AFFECTED IF ANY REMEDY PROVIDED HEREIN SHALL FAIL OF 
ITS ESSENTIAL PURPOSE.  
 
DISCLAIMER: Some countries, states, or provinces do not allow the exclusion or limitation of implied warranties or the limitation of incidental 
or consequential damages for certain products supplied to consumers, or the limitation of liability for personal injury, so the above limitations 
and exclusions may be limited in their application to you. When the implied warranties are not allowed to be excluded in their entirety, they will 
be limited to the duration of the applicable written warranty. This warranty gives you specific legal rights which may vary depending on local 
law.  
 
GOVERNING LAW: This Limited Warranty shall be governed by the laws of the State of Alabama, U.S.A. 

 

 

Summary of Contents for 900



















Reviews: