12 of 26
GT 710-8710 OPUS Low Energy Swing Doors Quick Set-Up and Parts Guide
www.NabcoEntrances.com
P/N C-00178
Rev 12-20-17
CHAPTER 6: INSTALL THE BOTTOM HALF OF INSWING ARM
SECTION 6 .1: Prepare the Swing Door for a Track With Reveal
1. Find the appropriate measurements for Reveal, and Track location within Table 4 or Table 5.
Table 4
Small Track Mounting Locations (12-1/4 inches)
Dim A
Dim B
Dim C
Dim A
Dim B
Dim C
Dim A
Dim B
Dim C
Reveal Butt Hinge Center Pivot
Reveal Butt Hinge Center Pivot
Reveal Butt Hinge
Center Pivot
0
7-5/8”
7-3/16”
2-3/4”
8-11/16”
9-3/8”
5-1/2”
14-1/2”
13-13/16”
1/4”
7-3/4”
7-3/8”
3”
13-1/8”
9-9/16”
5-3/4”
1/2”
7-15/16”
7-9/16”
3-1/4”
13-3/8”
13-1/16”
6”
3/4”
8-1/8”
7-3/4”
3-1/2”
13-9/16”
13-1/4”
6-1/4”
1”
8-5/16”
7-15/16”
3-3/4”
13-3/4”
13-1/2”
6-1/2”
18-1/2”
1-1/4”
8-1/2”
8-1/8”
4”
14”
13-11/16”
6-3/4”
18-9/16”
17-7/8”
1-1/2” 8-11/16”
8-5/16”
4-1/4”
14-3/16”
13-3/4”
7”
18-9/16”
17-7/8”
1-3/4”
8-7/8”
8-1/2”
4-1/2”
14-7/16”
7-1/4”
18-5/8”
17-15/16”
2”
8-1/16”
8-3/4”
4-3/4”
14-1/2”
7-1/2”
Long Track only
2-1/4”
8-1/4”
8-15/16”
5”
2-1/2”
8-1/2”
9-1/8”
5-1/4”
13-13/16”
Table 5
Large Track Mounting Locations (21 inches)
Dim A
Dim B
Dim C
Dim A
Dim B
Dim C
Reveal
Butt Hinge
Center Pivot
no Finger Guard
Reveal
Butt Hinge
Center Pivot
no Finger Guard
7-1/2” Short Track only
13-1/2”
10-1/2”
19-1/4”
13-9/16”
7-3/4”
14-1/4”
13-9/16”
10-3/4”
18-5/8”
8”
11”
18-11/16”
8-1/4”
13-5/8”
11-1/4”
19-5/16”
8-1/2”
11-1/2”
8-3/4”
11-3/4”
9”
12”
9-1/4”
12-1/4”
9-1/2”
12-1/2”
9-3/4”
12-3/4”
10”
13-9/16”
13”
10-1/4”
14-3/16”
2. Measure from the (Center Pivot or Butt Hinge) towards the center Face of Door according to Table 4 or Table 5. Mark a
Vertical Line at that location.
3. Go to the bottom of the Door Frame. Measure 1 - 11/16 inches down to the face of Door. Mark a Horizontal line across the
Vertical Line. This is the center of the first Sex Bolt hole.