8 of 31
GT1175 Slide Door Opus Control Wiring and Programming Manual
www.NabcoEntrances.com
P/N C-00391
Rev 8-11-21
Level One screens are used to inform the User all specifications that have already been programmed into the Opus Control. If a
specification needs to be changed, the User must reprogram the Opus Control within the Level Three screen, or Level Four screen.
When Power is turned ON for the first time, the Door does not move. Instead, an LCD screen will illuminate to display a Level One:
Unit Specification screen (Default screen).
There are (4) Level One screens:
X
Unit Specifications:
Displays the type of door and current status of the unit. The type of door (swing, slide or folding)
can be changed within the Base Settings Category (Level 3 and Level 4). Please refer to Subsection
The screen
above shows the Opus control installed on a GT710.
X
Error Specifications:
This screen will only display an Error Code in the event there is an Error. Otherwise this screen
stays blank.
DN 2431
Type:
GT710 Swing
Status:
Slow Closing
Error:
-----
Ac va on: IN EXT
Posi on:
> > > > > > >
Other:
BA 6B SLS
Keep Pushing Switch
=> Se ng Mode
UNIT SPECS
Recycle Warning!
Rotate
Dial
ERROR SPECS
Short
Push
FLASHING
SCREEN
Long
Push
Recycle Warning!
Clear Yes No
ERROR SPECS
Rotate
Dial
Recycle Warning!
Clear No
ERROR SPECS
Yes
Short
Push
Fully Closed
GT1175 Opus Slide
Figure 4
Example: Clear an Error Code for Recycle Warning
X
ANSI Specifications:
Displays the actual time of opening and closing of the door to help determine ANSI compliance.
(Applies to swing doors only).
X
Terminal Specifications:
Displays the current status of all of the Input/Output lines of the terminal strip.
SECTION 4.2 Level Two: Access Screen
Note: The “Activate Passcode” option is only displayed in the event “0045” had not already been entered.
DN 1713
Passcode
Stroke Learning
Yes No
LEVEL 2
Rotate
Dial
Passcode
Stroke Learning
Yes No
Passcode
Go to Se ng Menu
Stroke Learning
Passcode
Go to Se ng Menu
Stroke Learning
Go to Se ng menu
Reset to Default Set
Yes
No
Passcode
Stroke Learning
Yes No
Ac vate Passcode
Rotate
Dial
Rotate
Dial
Rotate
Dial
Figure 5
Level Two Screen
Attention: To prevent tampering, a Universal Passcode (0045) has been programmed into all Opus Controls. This
Passcode cannot be changed, but can be turned OFF and ON.
Attention: Do Not activate Passcode (0045) until programming of the Opus Control is complete. Failure to do so,
will force the User to enter (0045) each time a change is made.
SECTION 4.3 Enter Passcode
Short
Push
LEVEL 2
Reset to Default Set
If you don’t know
the passcode,
Keep Pushing Switch,
Return to Normal mode
0
Short
Push
Reset to Default Set
If you don’t know
the passcode,
Keep Pushing Switch,
Return to Normal mode
0 0
Short
Push
Reset to Default Set
If you don’t know
the passcode,
Keep Pushing Switch,
Return to Normal mode
0 0 0
Rotate
Dial
Reset to Default Set
If you don’t know
the passcode,
Keep Pushing Switch,
Return to Normal mode
0 0 4
Short
Push
Reset to Default Set
If you don’t know
the passcode,
Keep Pushing Switch,
Return to Normal mode
0 0 4 4
Rotate
Dial
0 0 4 5
Short
Push
Correct PassCode!
If you don’t know
the password,
Keep Pushing Switch,
Return to Normal mode
0 0 4 5
Reset to Default Set
If you don’t know
the passcode,
Keep Pushing Switch,
Return to Normal mode
DN 1715
Passcode
Stroke Learning
Yes No
Ac vate Passcode
