(2) DIGITAL OUTPUT.
The digital playback signal is available at this out-
put jack. The serial data output is taken after error
correction and de-interleaving, but before digital-to-
analog conversion and filtering. The output is
buffered to isolate it from the built-in D-to-A circuits.
It may be connected to any digital signal processor
that conforms to the Sony/Philips standard.
To use the digital output, connect a cable from this
jack to the “CD digital” or equivalent input on the digi-
tal processor. The cable must be a 75-ohm coaxial
cable of the type used for video signals, with an RCA
phono plug at each end. (To distinguish them from
similar phono-plug cables used for audio, video
cables often are color-coded with yellow plugs.)
(3) AC POWER CORD...
After completing the installation and all connec-
tions, make sure that the POWER switch on the front
panel of this unit is set to OFF. Then plug the power
cord into an AC wall outlet.
COMPACT DISCS -
HANDLING THE DISCS
Fingerprints and dust should be carefully wiped off
the disc’s playing surface (glossy side) with a soft
cloth.
Wipe using a straight motion from the inside to the
outside of the disc.
Never use chemicals such as record cleaning
sprays, antistatic sprays or fluids, benzine or thinner
to clean compact discs. These chemicals will perma-
nently damage the disc’s plastic surface.
Always place the compact disc in the disc tray with
the label facing upward. Compact discs can be
played on only one side.
To remove a disc from is storage case, press down
on the centre of the case and lift the disc out, holding
it carefully by the edges.
Discs should be returned to their cases after use to
protect them from dust and scratches.
To prevent warping the disc, do not expose it to
direct sunlight, high humidity or high temperatures for
extended periods of time. Do not apply paper or write
anything in the disc surface.
OPERATION OF THE DIGITAL COMPACT
DISC CHANGER
THE FIGURES IN BRACKETS REFER TO THE
LOCATION OF THE FRONT PANEL CONTROLS IN
FIGURE 2 AT THE FRONT OF THIS MANUAL.
POWER:
Press the green button (1, Fi. 2) IN to
switch on the CD Player. The display will illuminate.
To switch the POWER off, press the button again and
release it (Button OUT)
LOADING A DISC
1. Set the power button (1) to ON (button IN).
- The carousel turns clockwise automatically.
2. Press the OPEN/CLOSE button (4), and the
DISC TRAY will open.
3. Load the disc on the disc tray (2), label side up.
4. Press the NEXT DISC button (9) to load all 5
discs.
- Each time the NEXT DISC button is pressed, the
carousel turns clockwise to the next disc position.
NOTE:DO NOT TOUCH OR FORCE THE
CAROUSEL WHILE IT IS ROTATING.
CAUTION:
Do not put anything except a compact disc into the
tray.
Foreign objects can damage the mechanism.
PLAYING A DISC
1. Set the POWER button (1) to ON (button IN).
2. Press the OPEN CLOSE button (4).
3. Load a disc.
4. Press a DISC NO. button on the remote control
which corresponds to the tray number of the disc to
be played, or use the NEXT DISC button (9) on the
player to access the required disc.
- When a disc number has been selected, play will
start on track 1 of the selected disc.
5. Press the “>>I” or “I<<” (7) button to select a
track number, if a track other than track 1 is required.
- If only a track number is selected when in STOP
mode, play will start with the selected track of the cur-
rently displayed disc number.
NOTE:
If a track number is selected which is greater than
the highest track number on the disc, play will start
with the last track on the disc.
6. Press the PLAY button (3).
- The PLAY and EACH is displayed.
- The tracks elapsed playing time and the number
of the disc and track currently playing are displayed.
The number of the track currently playing will blink.
- During PLAY mode, select the disc and track
numbers, then within 10 seconds press the PLAY
button.
7. Press the TIME button on the remote control
once, twice, or three times to display the following
information:
Pressing once, shows how much of the track in
play is remaining in minutes and seconds.
Pressing twice,shows how many tracks are on the
current disc and the total playing time of the disc in
minutes and seconds.
Pressing three times shows the remaining number
of tracks and their combined remaining playing time
for the disc that is in play.
8. Press the TIME button on the remote control
again to view the current track’s elapsed playing time.
- During disc play, the TIME display will return to
the elapsed playing time indication about 10 seconds
after the TIME button has been pressed.
NAD
5
GB
