ENGLISH
WHAT’S IN THE BOX
Packed with your C 3050 you will find:
•
Two detachable mains power cord
•
SR 10 remote control with 2 AA batteries
•
Bluetooth antenna
•
Quick Setup Guide
SAVE THE PACKAGING
Please save the box and the packaging that came with your C 3050. Should
you move or need to transport your C 3050, this is the safest container
to use. We’ve seen too many otherwise perfect components damaged in
transit for lack of a proper shipping carton. So please, save that box!
CHOOSING A LOCATION
Choose a location that is well ventilated (with at least several inches to
both sides and behind), and that will provide a clear line of sight, within
23 feet/7 meters, between the C 3050’s front panel and your primary
listening/viewing position. This will ensure reliable infrared remote control
communications. The C 3050 generates a modest amount of heat, but
nothing that should trouble adjacent components. It is perfectly possible
to stack the C 3050 atop other components, but the reverse usually should
be avoided.
It is especially important that sufficient ventilation be provided. If you
are contemplating placing the C 3050 within a cabinet or other furniture,
consult your NAD audio/video specialist for advice on providing adequate
airflow.
NOTES ON INSTALLATION
•
Place your C 3050 on a firm, level surface.
•
Avoid placing the unit in direct sunlight or near sources of heat and damp.
•
Do not place the unit on a soft surface like a carpet.
•
Allow adequate ventilation.
•
Make sure the unit is switched off before making any connections.
•
Use high quality leads and sockets for optimum performance and reliability.
•
Ensure that leads and sockets are not damaged in any way and all
sockets are firmly pushed home.
•
Should water get into your C 3050, shut off the power to the unit and
remove the plug from the AC socket. Have the unit inspected by a
qualified service technician before attempting to use it again.
•
Use a dry soft cloth to clean the unit. If necessary, lightly dampen the
cloth with soapy water. Do not use solutions containing benzol or other
volatile agents.
DO NOT REMOVE THE COVER. THERE ARE NO USER-SERVICEABLE
PARTS INSIDE.
BARE WIRES AND PIN CONNECTORS
WARNING:
The terminals marked with this symbol are hazardous
live. External wiring connected to these terminals requires
installation by an instructed person or the use of ready-made leads
or cords.
Bare wires and pin sockets should be inserted into the hole in the shaft
of the terminal. Unscrew the speaker terminal’s plastic bushing until the
hole in the screw shaft is revealed. Insert the pin or bare cable end into
the hole and secure the cable by tightening down the terminal’s bushing.
Ensure bare wire from the speaker cables does not touch the back panel or
another socket. Ensure that there is only 1/2” (1cm) of bare cable or pin and
no loose strands of speaker wire.
FACTORY RESET
Factory reset is recommended if your C 3050 is malfunctioning or has
hanged up.
C 3050 can be factory reset or restored to factory default settings using the
following method.
1
With the C 3050 at operating mode, switch OFF the rear panel POWER
switch.
2
Press and hold the front panel POWER button and while doing so,
switch ON the rear panel POWER switch. Do not release hold of the
POWER button.
3
Hold down the POWER button for more than 30 seconds or until the VU
meter illuminates twice (white with yellow background). This indicates
that the factory reset is initiated. Release hold of POWER button.
4
The front panel Power LED indicator will turn off and then cycle to solid
amber. C 3050 factory reset is completed when the front panel Power
LED indicator turns solid amber and the VU meter not illuminated or
turned off.
IMPORTANT
Releasing the front panel POWER button at any time before the VU
meter illuminates twice will cancel the factory reset and leave the
C 3050 Upgrade Mode. Just start again the procedure for Factory Reset.
INTRODUCTION
GETTING STARTED
5
