ENGLISH
OPERATION
12
FREQ (HZ)
•
Grab the pointer of the “Hz” knob icon and rotate to set the frequency
level where the filter will be enabled. The frequency range available
is 20 Hz up to 20 kHz. The corresponding numerical value of adjusted
frequency level is reflected beside the knob icon. You can also type
directly desired frequency level in the section beside the “Hz” knob icon.
Q
•
“Q” setting refers to the depth the bandwidth can be adjusted. ”Q” level
is from 0.1 up to 24. Bandwidth is wider at lower Q level and narrower
with higher Q level.
GAIN
•
Grab the pointer of the “Gain” knob icon and rotate to set the dB level
the selected frequency can be increased or decreased. Gain level can
be set ±12 dB. The corresponding numerical value of adjusted dB level
is reflected beside the knob icon. You can also type directly desired dB
level in the section beside the “Gain” knob icon.
OFF/ON
•
Enable (On) or disable (Off) the Slope, Q, Hz and Gain settings by
selecting “On” or “Off” under their respective sections.
SETTINGS
POWER SETTINGS
POWER MODE
There are four methods the CI 8-120 can be powered up. Drag the slider
icon to one of the following power setting methods.
1
Power Button
2
Always On
3
12V Trigger
4
Signal Sense
POWER BUTTON
•
This is the default setting. CI 8-120 is powered up and powered down
by pressing front panel POWER button.
•
Power consumption of CI 8-120 is less than 1W while it is at network
standby mode.
NOTE
Network Standby mode maintains network connection at standby
mode with reduced system performance level.
ALWAYS ON
•
CI 8-120 will always be powered up and at operating mode. The unit
can only be normally powered down by switching to Power Button
method or unplugging the AC power cord from the mains power
outlet.
•
Power consumption is more than 80W while the unit remains powered
up.
12V TRIGGER
•
The function of powering up/down the CI 8-120 is dependent upon
the presence or absence of +12V DC supply at +12V TRIGGER IN (refer
also to item about +12V TRIGGER IN).
•
Ensure that the rear panel12V TRIGGER ON/OFF switch is set to ON so
that 12V TRIGGER power mode can function properly.
•
CI 8-120 can be switched remotely from standby mode to operating
mode and vice-versa by the compatible external device where +12V
TRIGGER IN -/+ terminals are connected.
•
Power consumption of CI 8-120 is less than 1W in the absence of +12V
DC supply at 12V TRIGGER IN.
SIGNAL SENSE
•
Signal sense feature enables CI 8-120 to wake up from standby mode
when triggered by active source input.
•
CI 8-120 will power up to the input source that activated the unit to
operating mode.
•
Power consumption of CI 8-120 is less than 1W while it is at network
standby mode.
ECO MODE
At Eco Mode ON setting, the amplifier will function as follows
•
Minimum power consumption of less than 0.5W.
•
Automatically goes to Eco standby mode after 20 minutes of no active
input signal.
•
At Signal Sense power mode, unit switches from Eco Standby mode to
operating mode when triggered by active input signal.
•
At 12V Trigger power mode, unit switches from Eco Standby mode to
operating mode when triggered by +12V Trigger source.
•
No network access at Eco standby mode.
Normal power settings are maintained at Eco Mode OFF setting.
POWER UP DELAY
•
Powering up CI 8-120 can be delayed by up 12 seconds. Drag the slider
icon to desired time delay setting (0 to 12 seconds).
•
You may use POWER UP DELAY to stagger turn on of the CI 8-120
especially if it is one of multiple pieces of electronic equipment
connected to the same electrical circuit.
