background image

文件编号

Doc. No.

NDT2920257

版次

Edition

2

Version 2

实施日期

Implementation date

2019-08-19

8

to insulation.

6

)温度降容。

(6) Temperature de-rating.

断路器安装场所的环境要求如下表

4

Environmental requirements for installation location of breaker are shown as follow Table 4:

4

断路器安装场所的环境要求

Table 4 Environmental requirements for installation location of breaker

项目

Item

规范

Specifications

周围空气温度

Ambient air 

temperature

-35

 

  +70

相对湿度

Relative 

humidity

(

+40

℃时

)

不超过

50%

,最低温度湿月最不超过

+25

℃,且该月平均最大相

对湿度不超过

90%,

并考虑因温度变化发生在产品表面上的凝露。

The relative humidity of the air does not exceed 50% (at +40

), the lowest 

temperature in the most humid month should not 25

, and the 

highest humidity in this month should not exceed 90% while condensation 

on breaker surface caused by temperature change should be taken into 

consideration.

海拔高度

Altitude

不超过

2000m

Lower than 2000m

污染等级

Pollution 

degree

3

Level 3

温度降容系数见下表

5

Temperature de-rating coefficient is shown as follow Table 5:

5

温度降容系数

Table 5 Temperature de-rating coefficient 

温度

Temperature

+40℃

+45℃

+50℃

+55℃

+60℃

+65℃

+70℃

降容系数

De-rating

Coefficient

1

1

1

0.978

0.957

0.934

0.911

注:当使用环境温度低于

40

时,产品可正常使用,不存在降容。

Notes

When ambient temperature is less than 40

, breaker can be used normally without any 

de-rating.

2019.12.31

文件控制

Summary of Contents for NDM3EU-400

















Reviews: