background image

Quick MGT-16 User Controls/Connections Guide

 

MT-16A/R Instrument Transmitter

ASC

TM 

IR Sync Download of Selected 

Frequency of MGT-16 Receiver to  

MT-16A/R, MH-16, LK-16 or WH-16 

Transmitter

(1)  

ASC

 IR SYNC INFRARED LED WINDOW

 

 For downloading selected Channel 
 (Frequency) to transmitter 

(21, 31, 46, 56) 

MT-16A/R, MH-16, LK-16, WH-16 

 TRANSMITTER IR RECEPTOR SENSOR/WINDOW

    

 Infrared LED sensor for linking the TX to the RX     

 during IR  frequency download.

(14) 

ASC

 IR SYNC BUTTON

 Press to make the IR link 

download the receiver’s selected frequency to the TX. 

First, turn on the system transmitter supplied (or turn 
off and then on again if already on) and position its 

IR window 6-12” away from the RX IR window, press 
the SYNC button once and wait one second for the RX 

to respond. If the IR data download is successful, the 
receiver 

SIGNAL LED (10)

 will light indicating the 

transmitter is locked in and transmitting. 

17

18

19

20

21

22

23

26

25

24

17. 

POWER SWITCH

 Slide in arrow direction 

to power transmitter On

18. 

15dB ATTENUATION PAD

 Select to 

reduce the input gain by 15dB for higher level 

audio input signals

19. 

INPUT ¼” PLUG

 Connect directly 

intoguitar/bass output jack

20. 

POWER &

 

LOW BATTERY LED

 Flashes 

once at power up, continous flashing indicates 

battery needs replacement

21. 

IR RECEPTOR SENSOR/WINDOW

 

Infrared LED sensor for linking the TX to the RX 

during IR frequency download

22. 

BATTERY COMPARTMENT

 Insert one AAA 

battery, observing correct polarity

23. 

INTERNAL AUDIO LEVEL ADJUST

 

Remove battery to access slot and adjust 

internal trim-pot with small screwdriver for 

optimal input level setting. 

Note: this is to be 

done only in rare cases as factory level setting 

is already optimized for most guitars and basses 

and 15dB Pad also available.Note: Set control 

carefully. If trim-pot is turned past minimum 

and maximum adjustment points it may need to 

be backed up to achieve desired setting. 

24. 

ANTENNA

 Permanently attached flexible 

antenna 

25. 

BATTERY

 Single AAA alkaline or NiMH 

battery required for operation

26. 

BATTERY COMPARTMENT COVER

 Slide 

to open

6

Summary of Contents for LINK-16





















Reviews: