1 Hardware Pack Contains:
PARTS LIST :
Instruction Sheet
2.5” Carriage Bolts
2.25” Hex Head Bolt
4” Hex Head Bolts
4.5” Hex Head Bolt
(1)
(5)
(1)
(3)
(1)
(15)
(8)
(10)
Tips for Assembly :
Tip 1: Do not tighten bolts completely until fully assembled
Tip 2: For a more uniform look, face all bolts in the same direction
ASSEMBLY :
Step 2 : Take a loose bar and insert a 4” hex head bolt through a washer before
pushing it through one of the holes at the end of the bar . Position this bar in-
side of the arm unit, put the end of the bolt in the hole, and then push the loose
bar flush with the arm unit before pushing the bolt through. Take a second loose
bar and attach it to the underside of the arm unit where the bolt is sticking out.
Attach with washer, lockwasher, and nut (See SIDE VIEW diagram). Repeat on the
other side.
Step 3 : Take the laminated rail (“J”-Piece) and place it half way between the arm
units. Position the end to fit between the two loose bars at the front of the swing.
Line up the holes and connect the three pieces together with a 4” hex head bolt,
secure on the other side with a washer, lockwasher, and nut.
Step 4 : Take the remaining loose bar and attach it to the lowest set of holes at
the top of the arm units and center “J” piece, using 2.5” carriage bolts. Secure
with washers, lockwashers, and nuts.
Step 5 : Arrange the chain sets so that the long piece faces the front of the
swing, and the short piece faces the back. Be sure chains are completely untwist-
ed.
Step 6 : Attach ‘top’ bar of the roll-up directly above the loose bar at the top of
the swing using the eyebolt found on the ‘short’ chain piece. The wooden strip
with brass tacks should face the back of the swing. (See sideview diagram).
Step 7 : Attach the ‘bottom’ bar of the roll up unit to the front of the swing using
the eyebolt on the ‘long’ chain piece (See sideview diagram). Attach the center of
the ‘J’ piece to the bottom of the roll-up unit with a 2.5” carriage bolt.
Step 8: Push the remaining 2.5” carriage bolt through the middle of the top roll-
up piece and ‘J’ piece. Secure with a washer, lockwasher, and nut.
Step 9: Look underneath the table top - the end with the metal plate faces front.
Align the holes in the back of the table assembly with the hole in the side of the
‘J’ piece. Place the 4.5” hex head bolt through a washer before pushing through
the wood. Secure with a washer, lockwasher, and nut.
Step 10: Lift the center table up and turn the metal piece so it points downward.
Drop the table top and align the metal plate with the hole in side of the ‘J’ piece.
Attach with a 2.25” hex head bolt. Note: The bolt will fit snugly through the
metal plate. Secure with washer and nut.
Step 11: Tighten all nuts.
DIAGRAM :
You Will Need :
Two 7/16” wrenches and a mallet or hammer
1 Roll-Up Unit : The “top” bar of the roll-up features a thin wooden strip with
brass tacks. The “bottom” bar has a thicker wooden strip attached with screws.
1 Chain Set : Chains come with eyebolts, nuts and washers attached. The longest
piece of chain will attach to the front/bottom of the swing, and the shortest piece
of chain will attach to the top/back of the swing.
2 Laminated Curved Arm Units
1 Laminated Curved Rail (“J”-Piece)
1 Center Table Unit
3 Loose Bars
Washers
Lock Washers
Nuts
Step 1 : Set arms upright on the floor about 60” apart. If sitting in the swing, the
branded arm will be on the right hand side.
