background image

16

n-SUB

Note:

 A special 4-pin DIN to stereo RCA Phono Plug lead is required 

for connection to Naim preamplifiers (usually via the preamplifier 
power supply). It incorporates resistors in the signal path to 
protect the preamplifier from the high capacitance inherent in the 
necessarily long lead.

Connect to the speaker level inputs using Naim speaker plugs 
via cables connected to the main (front left and right) speaker 
terminals. The stereo channels are combined to mono within 
the 

n-SUB. 

Speaker terminal “piggy-back” connectors and 

appropriate made-up cables will be available from your local 
Naim dealer or distributor.

USE OF THE SPEAKER LEVEL INPUTS WITH A NAIM NAP 500, 
OR ANY OTHER “BRIDGED” POWER AMPLIFIER, REQUIRES 
SPECIAL CONNECTION CABLES. CONTACT YOUR DEALER OR 
LOCAL DISTRIBUTOR FOR MORE INFORMATION.

Note:

 The decision to use either the line level or speaker level 

inputs when the n-SUB is not connected via an AV decoder can be 
made on the grounds of sound quality. It is impossible to predict 
which option will sound best in a particular system and installation, 
however the speaker level option, by virtue of higher signal levels 
being more robust over long lead lengths, is potentially superior.

Input sockets can be selected either directly from the 

n-SUB

 

control panel or included in a setup preset. See Section 11.3.

An RC5 control input is also provided on the 

n-SUB

 connection 

panel. This input can be used for wired remote control if the 

n-SUB

 is to be used out of line-of-sight in an installed audio 

system or if the n-SUB is one of a daisy-chained group.

11.2.2 n-SUB Outputs

The 

n-SUB

 is fitted with a mono signal output and an RC5 

control output, both on RCA Phono sockets. These output 
sockets are intended to enable “daisy-chaining” of one or more 

n-SUBs

 in systems where multiple sub-woofers are required. 

If these sockets are used take care to ensure that they are 
connected correctly.

11.2.3 Earth Terminal

An external earth (ground) terminal and earth selection switch 
are fitted to the underside of the 

n-SUB

. Use of the earth 

terminal may help alleviate audible hum from earth loops by 
disconnecting the signal and mains earths. If hum is a problem, 
connect the earth terminal with a single cable to the preamplifier 
earth terminal and move the switch to the “External” position.

Note:

 Do not switch the earth selection to External without an 

external earth connected.

11.3 n-SUB Configuration and Operation

With all input and output connections made and the 

n-SUB

 

positioned appropriately it is ready for configuration and 
operation.

Note:

 The n-SUB may be configured and operated from either its 

control panel or from the remote handset, however the handset 
provides enhanced functionality and direct access to gain and 
display control.

To select and adjust a parameter use the handset 

mode

5

or

mode

6

keys (control panel: 

mode

) to select. Once a parameter 

is selected use the handset 

up 

or 

down 

keys (control panel

:

 

up 

or 

down 

buttons) to adjust.

The handset and control panel 

mute 

function mutes and restores 

the 

n-SUB

 output.

The handset 

gain

5

 and 

gain

6

 keys provide direct control of 

n-SUB

 volume level. The handset 

disp 

key switches the control 

panel display on and off. The handset 

info 

key scrolls through 

and displays the parameter settings for the currently selected 
preset.

Note:

 Multiple daisy-chained n-SUBs should be initially configured 

from each control panel rather than from the remote handset. This 
removes the possibility of handset commands intended for one n-
SUB changing a previously defined configuration for another. Section 
11.4.5 covers the configuration of multiple n-SUBs, and the use of 
Lock Mode, in more detail.

11.3.1 n-SUB Presets

When first switched on from the control panel power button the 
display will show 

P1 

and the 

preset 

mode indicator will illuminate. 

P1 

indicates that preset P1 is loaded.

Note:

 If the n-SUB has not been previously used, all presets will 

contain the same default settings and values. If the n-SUB has 
been previously used some values and settings may vary from the 
defaults. To restore the factory defaults across all presets, press and 
hold the handset disp key for six seconds or switch the n-SUB off 
and then on while pressing the control panel mute button.

n-SUB

 presets contains a value or setting for each of the six 

variable parameters. These are 

gain

, low pass filter frequency 

(

freq

), 

invert

input

lock

, and 

label

. The function of each is 

described in Section 11.4.1 to Section 11.4.6.

To save a configuration preset once each parameter has been 
adjusted use the handset 

mode

5

 or 

mode

6

 keys (control 

panel: 

mode

) to select 

save, 

then use the handset 

up 

or 

down 

keys (control panel: 

up 

or 

down 

buttons) to select a preset 

number (

1

 to 

6

). Save the preset by pressing the handset 

save 

or 

mode

5

 keys (control panel: 

mode 

button). If the preset 

selected as the save location is the currently selected one it will 
be displayed with dashes either side (

-3-

).

Note:

 The handset save key can be used at any time to modify an 

existing preset following a parameter adjustment. Simply press and 
hold save.

To reset the currently selected preset to the factory default 
parameter values select 

save

 as described above and press and 

hold the handset 

disp 

key for six seconds.

11.4 n-SUB Configuration Parameters

11.4.1 Gain

Gain 

sets the volume level of the 

n-SUB

. The adjustment range 

is 

10 

to 

99

 and the factory default setting is 

40

. See Section 

11.5 for further guidance on setting this parameter.

11.4.2 Freq

Freq

 sets the upper filter frequency. This should generally be set 

as appropriate for the type of system and satellite speakers the 

n-SUB

 is to be integrated with. The adjustment range is 

20Hz 

to 

Summary of Contents for ALLAE - 2























Reviews: