background image

 

Naim Audio HDX Hard Disk Player – Network Setup 

4 September 2008 

 

Page 11 of 14 

Troubleshooting 

The Set IP Tool does not discover the HDX 

It is possible that a firewall running on the computer is blocking the communication between 
the  Set  IP  Tool  and  the  HDX.  If  this  is  suspected  to  be  the  case,  more  detailed  information 
about  how  to  allow  certain  applications  to  communicate  through  the  firewall  will  be 
available  from  the  firewall’s  vendor  website.  This  process  is  usually  known  as  ‘adding 
exceptions to a firewall’. 
 

Incorrect static address settings have been entered by accident 

Launch  the  Set  IP  Tool,  re-enter  the  details  and  click  update.  The  new  configuration  will  be 
sent to the HDX.  Alternatively return the HDX to DHCP  mode if the HDX was not intended to 
be set to static addressing mode. 

 
The front display permanently shows ‘Please Wait…’ 

The  most  likely  cause  is  that  the  HDX  has  been  configured  in  static  addressing  mode  with 
incompatible  settings.  Either  return  the  server  to  DHCP  mode  or  correct  the  static  address 
settings. Here are some examples of incompatible settings 
 

1)  Example 1 

Server IP = 192.168.0.

10

 

Front panel IP = 192.168.0.

10

 

Netmask = 255.255.255.0 

 
In this example the server and front panel IP addresses are identical. Two devices on a 
network must never have the same IP address. 

 

2)  Example 2 

Server IP = 192.168.

0

.10 

Front panel IP = 192.168.

1

.11 

Netmask = 255.255.255.0 

 

In  this  example  the  server  IP  and  front  panel  IP  addresses  are  on  different  address 
ranges.  The  IP  addresses  should  be  changed  so  the  first  three  parts  of  the  IP  are  the 
same. E.g. 192.168.0.10 and 192.168.0.11 

 

3)  Example 3 

Server IP = 

192.168.0.10

 

Front panel IP = 

10.15.35.50

 

Netmask = 255.255.255.0 

 
In  this  example  the  server  and  front  panel  IP  addresses  are  on  completely  different 
ranges.  This  can  happen  if  an  incorrect  configuration  is  sent  to  the  HDX  from  the 
NetStreams Dealer Setup application. Either correct the problem using the Set IP Tool 
or  check  the  addressees  allocated  to  the  HDX  and  front  panel  by  the  Dealer  Setup 
application. 

 

Summary of Contents for HDX - REMOTE CONTROL CODE















Reviews: