NAIM UNITIQUTE - Manual Download

Page: 15 / 23

UnitiQute Setup

If an incorrect passphrase or
access key is entered UnitiQute
will display an alert message.

Note:

As a security measure,

a router may also require the
UnitiQute’s MAC address to be
entered before allowing it to join the wireless network. This
type of security feature is known as ‘MAC address filtering’.
The UnitiQute MAC address is shown in the ‘Factory settings
> System Status’ page.

Note:

The wireless passphrase/access key is created when

the wireless router is first set up and could be a word or a
series of numbers and letters. If the passphrase/access key
is not known, check on the router settings page or with the
person who initially set up the router.

Note:

If a router offers multiple security configurations,

UnitiQute will automatically offer only the most
secure one.

Note:

If WEP security is used the router should be set

to “auto” or “open” authentication.

If the selected network is insecure
and requires no passphrase or
access key to join, UnitiQute will
display an alert message. Pressing
the handset

ok/list

key will

immediately connect UnitiQute
to the network and display a
confirmation screen.

Note:

Wireless connection difficulties can sometimes be

resolved by changing the wireless connection channel in
the router settings.

4.6.2 Non-DHCP (Static) Network

Connection

DHCP

is de-selected in the

Network Settings menu, five
further parameters will be
displayed.

Parameter

Options

User definable (numerical entry)
Default: 192.168.0.80

Mask:

User definable (numerical entry)

Default: 255.255.255.0

Gateway (Gtwy):

User definable (numerical entry)

Default: 192.168.0.1

DNS1:

User definable (numerical entry)

Default: 192.168.0.1

DNS2:

User definable (numerical entry)

Default: 192.168.0.1

These settings enable UnitiQute to connect to a network
using a fixed IP address. On selecting each one in turn,
numerical entry screens will be displayed that require
completion with the appropriate network IP address

settings. Consult your network router’s user documentation
for help with specifying fixed IP address settings.

4.7 The Digital Output Menu

The Digital Output setup menu
enables the UnitiQute digital
output to be switched on and its
signal format configured.

Parameter

Options

Enabled:

Yes / No

Output:

Native / 96kHz 24bit
If

Native

is selected, the digital output

format will reflect the input format. If

96kHz 24bit

is selected, the output is

re-sampled to 96kHz and 24bit resolution.

4.8 The Front Display Menu

The Front Display setup menu
enables the behaviour of
the front panel display, logo
illumination, clock display
and logo touch-muting to
be modified. The options are
tabulated and described in the following section:

Parameter

Options

Off During Mute:

Yes / No

Auto Off:

Select time from list

Clock When Off:

Yes / No

Logo Off:

If Muted / If Display Off / Always / Never

Logo Mute:

Yes / No

When

Off During Mute

is selected the front panel display

will switch off when mute is engaged.

Auto Off

defines the

length of time the display will remain switched on after
the last interface operation is carried out. Time periods of
between 10 seconds and 1 hour can be selected.

Note:

If the display has been switched off using the

handset disp key this setting will take priority over the Auto
Off setting. The display will always switch on briefly when
control commands are received.

The

Clock When Off

settings enables the clock to remain

displayed when other display settings are switched off.

Note:

If Clock When Off is set to “Yes” and Logo Off is set

to “If Muted”, the clock display will dim automatically 10
seconds after mute is selected.

The

Logo Off

settings select the circumstances in which

the front panel logo illumination will switch off.

Logo Mute