![background image](http://html2.mh-extra.com/html/nakayama/es2001/es2001_translation-of-the-original-instructions_3151450015.webp)
15
Important! The grinding depth should be set so
that the full cutting edge of the cutting link is
sharpened.
6.5 Lock the chain (Fig. 7)
. Tighten the chain locking screw (1)
6.6 Grind the link (Fig. 10/11)
. Switch the appliance on at the ON/OFF switch
(9/B1)
. Carefully bring the grinding wheel (5) with
grinding head (4) so that it is against the set link
. Switch the appliance off at the ON/OFF switch
(9/B1) Every second link in the chain must be
sharpened in this way. To know when every
second link in the entire chain has been
sharpened, mark the first link (e.g. with chalk).
Once all cutting links on one side have been
sharpened, the grinding angle must be set to the
same number of degrees on the other side.
You can then begin to sharpen the links of the
other side(without having to make any further
adjustments).
6.7 Set the depth limiter spacing (Fig. 12/13)
Once the chain has been fully sharpened, you
must make sure that the depth limiter spacing is
kept (the depth limiters (1) must be lower than
the cutting links (2). You may need to file the
depth limiters (1) to the specifications for your
chain using a file (3) (not included in delivery).
7. Cleaning, maintenance and ordering
of spare parts
Always pull out the mains power plug before
starting any cleaning work.
7.1 Cleaning
Keep all safety devices, air vents and the motor
housing free of dirt and dust as far as possible.
Wipe the equipment with a clean cloth or blow it
with compressed air at low pressure.
We recommend that you clean the tool
immediately after you use it.
Clean the equipment regularly with a moist cloth
and some soft soap. Do not use cleaning agents
or solvents; these may be aggressive to the tool's
plastic parts. Ensure that no water can get into
the interior of the tool.
7.2 Changing the grinding wheel
Important! Always switch the appliance off and
unplug the power plug before carrying out any
maintenance.
1. Remove the grinding wheel (Figs. 14-17)
2. Fit a new grinding wheel
3. Assemble in reverse order
Do not use grinding wheels that are worn,
broken, cracked or otherwise damaged.
Use only genuine grinding wheels.
8. Disposal and recycling
The unit is supplied in packaging to
prevent its being damaged in transit.
This packaging is raw material and can
therefore be reused or can be returned
to the raw material system.
The unit and its accessories are made of various
types of material, such as metal and plastic.
Defective components must be disposed of as
special waste. Ask your dealer or your local
council.
Summary of Contents for ES2001
