EN
WWW.NAKAYAMATOOLS.COM
3
Technical Data
Working pressure:
0.2-0.4 Mpa
DC12V capacity:
8Ah
Chemical Tank:
18L
Net weight:
6.4kg
* The manufacturer reserves the right to make minor changes to product design and technical
specifications without prior notice unless these changes significantly affect the performance and
safety of the products. The parts described / illustrated in the pages of the manual that you hold in
your hands may also concern other models of the manufacturer's product line with similar features
and may not be included in the product you just acquired.
* Please note that our equipment has not been designed for use in commercial, trade or industrial
applications. Our warranty will be voided if the machine is used in commercial, trade or industrial
businesses or for equivalent purposes.
* To ensure the safety and reliability of the product and the warranty validity, all repair, inspection,
repair or replacement work, including maintenance and special adjustments, must only be carried
out by technicians of the authorized service department of the manufacturer.
Operating instructions
Introduction of the function
As shown in figures, Control system are installed on one side of the cover :Voltmeter ,Speed Regulator, Charging Plug, Power Switch
Voltmeter, Indicate over-discharge, over-charge and normal service condition
Speed Regulator: adjust the rotating speed of pump to make the pump work stably, achieving the result of spraying stabilization
Charging plug: linked with charger to transmit energy to battery
Power switch : control the connection between the power and diaphragm pump
Under-voltage protector: optional, linked with speed regulator to protect battery
When the battery voltage reached the setted protecting voltage 9.5-10V, buzzer works, at this time, you should stop working to charge battery for mainte-
nance
Charging the battery
● The new machine must be charged before using.
● The deposit machine for a longtime must be charged before using
● Charging with special charger
Please untie the belt and back mat to reveal the battery completely. When charging, you only insert the output of the charger to the jack and then connect
the input with 220V alternating current. The signal light of the charger is red while normal charging. It will change into green when it’s full.
The conditions of using charger:
● The time of charging of new machine or deposit machine for a long time must reach 24 hours.
● Don’t let the switch in the place of “-” while charging.
● Please pull out the wire of charger from the jack after ending the charging.
● Don’t mistake the wire of the battery, or it will burn the battery and charger. The red wire should be connected with the red end of the battery.
● Don’t charge in wet room or with wet hands, or you will get an electric shock.
● Please use the special charger for this machine in order to avoid fire. In addition, it is prohibited to charge other electrical machines with the special charg-
er of this machine or as the power.
● Please pull out the wire of the battery from the socket after ending the charging
● Don’t let this machine in the sun, high temperature condition and the things radiating heat, or it will accelerate the old of the battery, make the battery
leak liquids, radiate heat, split and fire.
● If you find the charger abnormal, pull out the plug immediately in order to avoid electric shock, radiating heat and making fire.
● Don’t adopt generator as the electrical source of charging, or it will destroy the charger.
● Don’t pull the wire of charger forcibly.
Nut
Round bar
Spray nozzle
The connection of spraying parts
A. Fixing the spraying pole on the place shown in the figures.
B. Insert the spraying pole into the switch and fasten the screw cap.
Caution: Don’t fasten the nut with the pliers, or it maybe harm the nut.
C. Hold the knob assembly with one hand, t adjust the direction of the nozzle by holding the spraying head with the other hand.
D. If you want to spray higher crop, you could connect two spraying poles with the connections to longer the spraying pole.
E. This machine has three different kinds of nozzles. You could use the nozzle according to the different conditions.
Round Bar
Join
Nut
Round bar
● Please clean the electrical pickoff of the battery with dry cloth. Bad connection will cut the power supply or result in failing to charging.
● Be sure of safe, please store this machine in place out of the reach of children and infant in order to avoid get an electric shock.
If the battery of this machine need replace, it must be confirmed by company. The disabled battery couldn’t be thrown away anywhere. Please send it into
the qualified recycle center to deal with it.
