background image

 Exhaust gas

Exhaust gases contain carbon monoxide. This colour-

less and odourless gas is extremely harmful and could 

lead to poisoning which could result in loss of conscious-

ness or death. The first symptoms of carbon monoxide 

intoxication are as follows:

Dizziness

Nausea

Headache

Throbbing temples

Vomiting

Fatigue and falling asleep

Tense muscles

If you or anyone else in the vicinity of the generating set 

experiences any of these symptoms, leave the area of 

operation of the generating set and find fresh air. If the 

symptoms persist, consult a doctor and have your gen-

erating set checked.

 Risk of electric shock

Never touch the electrical connectors when the gener-

ating  set  is  operational. The  voltage  at  the  connector 

terminals can be lethal.
Do not work on the generating set without protection: 

protective goggles and gloves, insulating blankets etc.
Always disconnect the generating set and cut the cur-

rent before working on the electrical system. Isolate the 

shore  power  supply  to  all  the  electrical  circuit  equip-

ment.
Ensure  your  clothing  and  skin  is  not  damp  or  sweaty 

when  handling  electrical  equipment.  Remove  watch-

es, bracelets and jewellery when working on electrical 

equipment.
Handling a capacitor that is still charged can be danger-

ous and cause electrocution. 

 Risk of burns

Never touch the hot parts of the generating set or the 

exhaust circuit. 
An operational generating set gets very hot: the exhaust 

elbow and pipe, turbocompressor, starter, oil sump, oil, 

coolant in the hoses and pipes are hot and can burn. 
Always check the coolant level before starting the gen-

erating set.
Fluids ejected under pressure can cause serious injury. 
Release all the pressure in the circuits before removing 

the caps. 
Never open the coolant and oil circuit caps when the 

generating set is operational and/or hot. 
Never start or run the generating set when the oil fill cap 

is not screwed on as hot oil could spray out. 

If you come into contact with any of these fluids, consult 

a doctor immediately. 
If the generating set gets too hot, switch it off and dis-

connect it and wait for it to cool down before handling.

 Risk of fire

Do not smoke near the generating set and keep it away 

from sources of ignition (flames or sparks) or any other 

potential flammable vapour or liquid sources. 
Do not run the generating set without an air filter. 
Do not run the generating set in an area in which flam-

mable or explosive materials are stored or where gas is 

present. Ensure there are no flammable liquids in the 

engine compartment.
Immediately clean up any liquids spilled over yourself or 

the floor and keep the engine compartment clean and 

accessible so as to minimise the risk of fire. Be careful 

as fuel can burn.

 Risk of explosion

Explosions  caused  by  fuel  vapour  can  cause  serious 

injury! Carefully follow the safety rules when filling the 

fuel. 
Open and ventilate the storage area of the generating 

set after filling. Check that there are no fuel vapours or 

leaks before starting the fan (if fitted). Switch the fan on 

for 5 minutes before starting the generating set.
All fuel vapours are flammable and explosive. Be care-

ful when handling and storing fuel. Store the fuel in a 

ventilated area away from sources of ignition (sparks or 

flames) and out of the reach of children.
Stop the generating set before filling with fuel or lubri-

cant. Do not smoke near the generating set and keep it 

away from sources of ignition (flames) when filling with 

fuel  and/or  lubricant.  Wear  gloves  when  investigating 

possible leaks. 
Do not alter or damage the fuel circuit. Close the fuel 

circuit whenever you work on it.
Ensure you always have an appropriate working extin-

guisher to hand.

Safety precautions 

5

Summary of Contents for QLS 10T



























Reviews: