background image

 Accidental starting

Accidental starting can cause serious injury and even 

death! 
Disconnect the battery before working on the generat-

ing set. 
Ensure no one is alongside the generating set or work-

ing on the set before starting it. 
Ensure all the protection mechanisms are in place be-

fore starting the generating set.

 Risk of battery explosion

A battery explosion can cause serious injury and even 

death!
Do not smoke near the batteries and keep them away 

from sources of ignition (flames or sparks). They pro-

duce hydrogen which could ignite or explode on contact 

with an electrical arc or a flame. Switch off all electrical 

appliances in the vicinity when you are working on the 

batteries.  Ensure  the  battery  storage  compartment  is 

corrected ventilated.
Avoid touching the battery terminals with metal tools so 

that  no  sparks  are  created  which  could  cause  an  ex-

plosion.  Remove  your  rings,  bracelets  and  necklaces 

before handing the batteries.

 Battery acid

The acid in batteries can cause serious injury and even 

death!
When  servicing  the  batteries,  wear  protective  gloves 

and goggles. Batteries contain sulphuric acid which is 

highly corrosive. 
Acid can spurt from batteries when they are handled. 

If the acid comes into contact with the skin, rinse thor-

oughly in fresh water and consult a doctor. 

 Exhaust gas

Ensure the exhaust circuit correctly expels the gas pro-

duced by the generating set.
 Regularly check that the exhaust circuit is free of leaks 

and that the exhaust elbow is correctly affixed.
Operate the generating set in a well aerated and ven-

tilated area away from other people. Run the fan when 

the generating set is operational.

 Rotating parts

Rotating parts can be extremely dangerous and cause 

serious injury and even death! 
Do not work on the generating set when it is operational. 

If work on the engine when running is absolutely neces-

sary, do not touch any hot or rotating parts. 
Baggy clothing, hair or objects could be pulled in and/or 

caught and cause serious injury or substantial property 

damage. 

Do not wear bracelets, necklaces or rings when working 

on a generating set.
Check that the bolts and screws are properly tightened 

and that the protection mechanisms are in place.
Do not check the fluid levels or tension of the alternator 

belt when the generating set is operational.

 Lifting the generating set

To lift the generating set, use the hoisting eyes on the 

appliance. 
Always check the robustness and overall condition of 

the lifting equipment. Use suitable gear (cables, beams, 

machines, etc.) to lift your generating set. Check that 

your gear is capable of lifting the set. 
Lifting cables and chains must be able to move parallel 

to each other. 
Do not forget that any additional equipment mounted on 

the generating set could alter its centre of gravity. When 

lifting the set, it should remain as parallel as possible to 

the ground. 

 Maintenance and spare parts

Nanni Diesel engines are designed to meet the different 

emission standards while delivering maximum service 

life and reliability. 
Regularly  servicing  and  replacing  parts  with  original 

Nanni Diesel parts will ensure the generating set con-

tinues to function optimally. 
These parts can be ordered from all Nanni Diesel deal-

ers throughout the world.

 Chemical products

The different fluids used to run the generating set are a 

health hazard. 
Carefully  read  the  instructions  on  the  packaging  of 

these products and always check that the ventilation in 

the hold space is adequate.

6

Safety precautions 

Summary of Contents for QLS 10T



























Reviews: