background image

XCD Edge Motherboard

 

User Guide

 

 

Limited Warranty

 

D/N: XCDE458100, Revision B 

 

 3 

Limited Warranty 

Nanomotion Ltd. (hereinafter NM) warrants the product (other than software) 

manufactured by it to be free from defects in material and workmanship for a period 

of time of one year (except those parts normally considered as 

consumable/expendable components such as motor conditioning brushes). The 

warranty commences thirty (30) days from the date of shipment. 

NM warrants those parts replaced under warranty for a period equal to the remaining 

warranty coverage of the original part. 

NM’s sole and exclusive obligation under this warranty provision shall be to repair, or 

at its sole option exchange defective products or the relevant part or component, but 

only if: (i) the Purchaser reports the defect to NM in writing and provides a description 

of the defective product and complete information about the manner of its discovery 

within ten (10) days of its discovery; (ii) NM has the opportunity to investigate the 

reported defect and to determine that the defect arises from faulty material, parts or 

workmanship; and (iii) the Purchaser returns the affected product to a location 

designated by NM.  These provisions constitute the exclusive remedy of the 

Purchaser for product defects or any other claim of liability in connection with the 

purchase or use of NM products. 

This warranty policy applies only to NM products purchased directly from NM or from 

an authorized NM distributor or representative. 

This warranty shall not apply to (i) products repaired or altered by anyone other than 

those authorized by NM; (ii) products subjected to negligence, accidents or damage 

by circumstances beyond NM control; (iii) product subjected to improper operation or 

maintenance (i.e. operation not in accordance with NM Installation Manuals and/or 

instructions) or for use other than the original purpose for which the product was 

designed to be used. 

NM shall not in any event have obligations or liabilities to the Purchaser or any other 

party for loss of profits, loss of use or incidental, increased cost of operation or delays 

in operation, special or consequential damages, whether based on contract, tort 

(including negligence), strict liability, or any other theory or form of action, even if NM 

has been advised of the possibility thereof, arising out of or in connection with the 

manufacture, sale, delivery, use, repair or performance of the NM products.  Without 

limiting the generality of the preceding sentence, NM shall not be liable to the 

Purchaser for personal injury or property damages. 

 

Summary of Contents for XCD EDGE


























Reviews: